TSC2003

14

SBAS162D

www.ti.com

SDA

SCL

Slave Address

Repeated If More Bytes Are Transferred

R/W

Direction

Bit

Acknowledgement

Signal from

Receiver

Acknowledgement

Signal from

Receiver

START

Condition

12

7

6

8

9

1

2

3-7

8

9

ACK

ACK

STOP Condition

or Repeated

START Condition

serial clock (SCL), controls the bus access, and generates

the START and STOP conditions. The TSC2003 operates as

the open-drain I/O lines SDA and SDL.

The following bus protocol has been defined, as shown in

Figure 9:

•

Data transfer may be initiated only when the bus is not busy.

•

During data transfer, the data line must remain stable

whenever the clock line is HIGH. Changes in the data line

while the clock line is HIGH will be interpreted as control

signals.

Accordingly, the following bus conditions have been defined:

Bus Not Busy: Both data and clock lines remain HIGH.

Start Data Transfer: A change in the state of the data line,

from HIGH to LOW, while the clock is HIGH defines a START

condition.

Stop Data Transfer: A change in the state of the data line,

from LOW to HIGH, while the clock line is HIGH defines a

STOP condition.

Data Valid: The state of the data line represents valid data

when, after a START condition, the data line is stable for the

duration of the HIGH period of the clock signal. There is one

clock pulse per bit of data.

Each data transfer is initiated with a START condition and

terminated with a STOP condition. The number of data bytes

transferred between START and STOP conditions is not

limited, and is determined by the master device. The informa-

tion is transferred byte-wise, and each receiver acknowl-

edges with a ninth-bit.

clock rate), a fast mode (400kHz clock rate), and a

high-speed mode (3.4MHz clock rate) are defined. The

TSC2003 works in all three modes.

Acknowledge: Each receiving device, when accessed, is

obliged to generate an acknowledge after the reception of

each byte. The master device must generate an extra clock

pulse, which is associated with this acknowledge bit.

A device that acknowledges must pull down the SDA line during

the acknowledge clock pulse in such a way that the SDA line is

stable LOW during the HIGH period of the acknowledge clock

pulse. Of course, setup and hold times must be taken into account.

A master must signal an end of data to the slave by not generating

an acknowledge bit on the last byte that has been clocked out of

the slave. In this case, the slave must leave the data line HIGH to

enable the master to generate the STOP condition.

bus. Depending upon the state of the R/W bit, two types of

data transfer are possible:

•

Data transfer from a master transmitter to a slave

receiver. The first byte transmitted by the master is the

slave address. Next follows a number of data bytes. The

slave returns an acknowledge bit after the slave address

and each received byte.

•

Data transfer from a slave transmitter to a master

receiver. The first byte (the slave address) is transmitted

by the master. The slave then returns an acknowledge bit.

Next, a number of data bytes are transmitted by the slave

to the master. The master returns an acknowledge bit

after all received bytes other than the last one. At the end

of the last received byte, a ‘not acknowledge’ is returned.

The master device generates all of the serial clock pulses

and the START and STOP conditions. A transfer is ended

with a STOP condition or a repeated START condition. Since

a repeated START condition is also the beginning of the next

serial transfer, the bus will not be released.

The TSC2003 may operate in the following two modes:

•

Slave Receiver Mode: Serial data and clock are received

through SDA and SCL. After each byte is received, an

acknowledge bit is transmitted. START and STOP condi-

tions are recognized as the beginning and end of a serial

transfer. Address recognition is performed by hardware

after reception of the slave address and direction bit.

•

Slave Transmitter Mode: The first byte (the slave ad-

dress) is received and handled as in the slave receiver

mode. However, in this mode the direction bit will indicate

that the transfer direction is reversed. Serial data is

transmitted on SDA by the TSC2003 while the serial clock

is input on SCL. START and STOP conditions are recog-

nized as the beginning and end of a serial transfer.