CP20.241-R1, CP20.241-R2, CP20.241-R3,

CP20.242-R2, CP20.242-R2-C1

CP-Series

Jan. 2018 / Rev. 0.2 DS-CP20.241-R2-EN - All parameters are typical values specified at 230Vac, 50Hz input voltage, 24V, 20A output

load, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0

Germany

18/33

P R E L I M I N A R Y

16. EMC

The EMC behavior of the device is designed for applications in industrial environment as well as in residential,

commercial and light industry environments.

EMC Immunity

According generic standards: EN 61000-6-1 and EN 61000-6-2

Electrostatic discharge

EN 61000-4-2

Contact discharge

Air discharge

8kV

15kV

Criterion A

Criterion A

Electromagnetic RF field

EN 61000-4-3

80MHz-2.7GHz

20V/m

Criterion A

Fast transients (Burst)

EN 61000-4-4

Input lines

Output lines

DC-OK signal (coupling clamp)

4kV

2kV

2kV

Criterion A

Criterion A

Criterion A

Surge voltage on input

EN 61000-4-5

L

N

L

PE, N

PE

2kV

4kV

Criterion A

Criterion A

Surge voltage on output

EN 61000-4-5

+

-

+ / -

PE

1kV

2kV

Criterion A

Criterion A

Surge voltage on Signals

EN 61000-4-5

DC-OK signal

PE

1kV

Criterion A

Conducted disturbance

EN 61000-4-6

0.15-80MHz

20V

Criterion A

Mains voltage dips

EN 61000-4-11

0% of 100Vac

40% of 100Vac

70% of 100Vac

0% of 200Vac

40% of 200Vac

70% of 200Vac

0Vac, 20ms

40Vac, 200ms

70Vac, 500ms

0Vac, 20ms

80Vac, 200ms

140Vac, 500ms

Criterion A

Criterion C

Criterion C

Criterion A

Criterion A

Criterion A

Voltage interruptions

EN 61000-4-11

0% of 200Vac (=0V)

5000ms

Criterion C

Voltage sags

SEMI F47 0706

Dips on the input voltage according to SEMI F47 standard

80% of 120Vac (96Vac)

70% of 120Vac (84Vac)

50% of 120Vac (60Vac)

1000ms

500ms

200ms

Criterion A

Criterion A

Criterion A

Powerful transients

VDE 0160

Over entire load range

750V, 0.3ms

Criterion A

Criterions:

A:

Power supply shows normal operation behavior within the defined limits.

C:

Temporary loss of function is possible. Power supply may shut-down and restarts by itself. No damage or hazards for the power supply

will occur.

EMC Emission

According generic standards: EN 61000-6-3 and EN 61000-6-4

Conducted emission

input lines

EN 55011, EN 55015, EN 55022, FCC Part

15, CISPR 11, CISPR 22

Class B

Conducted emission

output lines

IEC/CISPR 16-1-2, IEC/CISPR 16-2-1

T.B.D. for information only, not

mandatory for EN 61000-6-3

Radiated emission

EN 55011, EN 55022

Class B

Harmonic input current

EN 61000-3-2

Class A fulfilled between 0A and 12A load

Class C fulfilled between 6A and 12A load

Voltage fluctuations, flicker

EN 61000-3-3

Fulfilled, tested with constant current

loads, non pulsing

This device complies with FCC Part 15 rules.

Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.