| 数据搜索系统,热门电子元器件搜索 |
|
M41ST95W 数据表(PDF) 27 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
M41ST95W 数据表(HTML) 27 Page - STMicroelectronics |
|
27 / 35 page ![]() 27/35 M41ST95Y*, M41ST95W Table 13. DC Characteristics Note: 1. Valid for Ambient Operating Temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted). 2. Measured with VOUT and ECON open. 3. RSTIN1 and RSTIN2 internally pulled-up to VCC through 100KΩ resistor. WDI internally pulled-down to VSS through 100KΩ resistor. 4. Outputs Deselected. 5. External SRAM must match RTC SUPERVISOR chip VCC specification. 6. For rechargeable back-up, VBAT(max) may be considered VCC. 7. For PFO, F32k, and SQW pins (CMOS). 8. Conditioned output (ECON) can only sustain CMOS leakage current in the battery back-up mode. Higher leakage currents will re- duce battery life. 9. For IRQ/FT/OUT, RST pins (Open Drain); if pulled-up to supply other than VCC, this supply must be equal to, or less than 3.0V when VCC = 0V (during battery back-up mode). Sym Parameter Test Condition(1) M41ST95Y M41ST95W Unit Min Typ Max Min Typ Max IBAT (2) Battery Current OSC ON TA = 25°C, VCC = 0V, VBAT = 3V 400 550 400 550 nA Battery Current OSC OFF 50 50 nA ICC1 Supply Current f = 2MHz 2 2 mA ICC2 Supply Current (Standby) SCL, SDI = VCC – 0.3V 1.4 1.4 mA ILI (3) Input Leakage Current 0V ≤ VIN ≤ VCC ±1 ±1 µA Input Leakage Current (PFI) –25 2 25 –25 2 25 nA ILO (4) Output Leakage Current 0V ≤ VIN ≤ VCC ±1 ±1 µA IOUT1 (5) VOUT Current (Active) VOUT1 > VCC – 0.3V 175 100 mA IOUT2 VOUT Current (Battery Back-up) VOUT2 > VBAT – 0.3V 100 100 µA VIH Input High Voltage 0.7VCC VCC + 0.3 0.7VCC VCC + 0.3 V VIL Input Low Voltage –0.3 0.3VCC –0.3 0.3VCC V VBAT Battery Voltage 2.5 3.0 3.5(6) 2.5 3.0 3.5(6) V VOH Output High Voltage(7) IOH = –1.0mA 2.4 2.4 V Power Supply Voltage (Open Drain) IRQ/FT/OUT, RST 5.5 3.6 V VOHB (8) VOH (Battery Back-up) IOUT2 = –1.0µA 2.5 2.9 3.5 2.5 2.9 3.5 V VOL Output Low Voltage IOL = 3.0mA 0.4 0.4 V Output Low Voltage (Open Drain)(9) IOL = 10mA 0.4 0.4 V VPFD Power Fail Deselect 4.20 4.40 4.50 2.55 2.60 2.70 V VPFI PFI Input Threshold VCC = 5V(Y) VCC = 3V(W) 1.225 1.250 1.275 1.225 1.250 1.275 V PFI Hysteresis PFI Rising 20 70 20 70 mV VSO Battery Back-up Switchover 2.5 2.5 V |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |