AM29DL642G datasheet(25/54 Pages) AMD

25 / 54 page

June 10, 2005

Am29DL642G

PRELIMINARY

power-up and power-down. The command register

and all internal program/erase circuits are disabled,

and the device resets to the read mode. Subsequent

writes are ignored until V

CC is greater than VLKO. The

system must provide the proper signals to the control

pins to prevent unintentional writes when V

CC is

greater than V

LKO.

Write Pulse “Glitch” Protection

Noise pulses of less than 5 ns (typical) on OE#, CE#

or WE# do not initiate a write cycle.

Logical Inhibit

Write cycles are inhibited by holding any one of OE# =

VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,

CE# and WE# must be a logical zero while OE# is a

logical one.

Power-Up Write Inhibit

If WE# = CE# = V

IL and OE# = VIH during power up,

the device does not accept commands on the rising

edge of WE#. The internal state machine is automati-

cally reset to the read mode on power-up.

COMMON FLASH MEMORY INTERFACE

(CFI)

The Common Flash Interface (CFI) specification out-

lines device and host system software interrogation

handshake, which allows specific vendor-specified

software algorithms to be used for entire families of

devices. Software support can then be device-inde-

pendent, JEDEC ID-independent, and forward- and

backward-compatible for the specified flash device

families. Flash vendors can standardize their existing

interfaces for long-term compatibility.

This device enters the CFI Query mode when the sys-

tem writes the CFI Query command, 98h, to address

55h, any time the device is ready to read array data.

The system can read CFI information at the addresses

given in Tables 9–12. To terminate reading CFI data,

the system must write the reset command.The CFI

Query mode is not accessible when the device is exe-

cuting an Embedded Program or embedded Erase al-

gorithm.

The system can also write the CFI query command

when the device is in the autoselect mode. The device

enters the CFI query mode, and the system can read

CFI data at the addresses given in Tables 9–12. The

system must write the reset command to return the

device to reading array data.

For further information, please refer to the CFI Specifi-

cation and CFI Publication 100, available via the World

Wide Web at http://www.amd.co m /us-en/as-

sets/content_type/DownloadableAssets/cfi100.pdf and

http://www.amd.com/us-en/assets/content_type/Down

loadableAssets/cfiamd1.pdf. Alternatively, contact an

AMD representative for copies of these documents.

Table 9.

CFI Query Identification String

Addresses

Data

Description

10h

11h

12h

0051h

0052h

0059h

Query Unique ASCII string “QRY”

13h

14h

0002h

0000h

Primary OEM Command Set

15h

16h

0040h

0000h

Address for Primary Extended Table

17h

18h

0000h

Alternate OEM Command Set (00h = none exists)

19h

1Ah

0000h

Address for Alternate OEM Extended Table (00h = none exists)

AM29DL642G 数据表(PDF) 25 Page - Advanced Micro Devices

AM29DL642G 数据表(HTML) 25 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

数据表下载

链接网址

AM29DL642G 数据表(PDF) 25 Page - Advanced Micro Devices

AM29DL642G 数据表(HTML) 25 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

数据表 下载

链接网址

数据表下载