MODEL: AD2LC

AD2LC SPECIFICATIONS

ES-1388 Rev.14 Page 4/7

https://www.m-system.co.jp/

PARAMETER LIST

It is available to configure or confirm settings shown below by using front key pad.

ITEM

MDF.

CODE

DATA

CONTENTS

DEFAULT

P

N/A

-9999 – 9999

(-FFFF – FFFF)

Output display in engineering unit, BCD (as set in ITEM 17/18)

( ) for binary, offset binary, two’s complement, re ected binary

----

01

1, 2

Modi cation code

1 : Data indication only.

2 : All parameters are modi able.

1

02

N/A

0 – 99

Status indication (“0” is normally indicated.)

----

03

N/A

0, 1, 2

Input range code

0 : S1 (0.0 – 3.0mV/V)

1 : S2 (0.0 – 10.0mV/V)

2 : S3 (0.0 – 30.0mV/V)

User speci ed

04

2

0.1 – 12.0

Excitation voltage (V)

1.0V

05

2

0.010 – 3.000

0.010 – 9.999

0.10 – 30.0

Sensor sensitivity

S1 : 0.0 – 3.0mV/V

S2 : 0.0 – 10.0mV/V

S3 : 0.0 – 30.0mV/V

Used when adjusting the sensor sensitivity by its rating value.

Set ITEM 06 before 05.

3.000

9.999

30.00

06

2

-30.00 – 30.00

-99.99 – 99.99

-300.0 – 300.0

0% input voltage

S1 : -30.00 – 30.00mV

S2 : -99.99 – 99.99mV

S3 : -300.0 – 300.0mV

Sensor’s zero adjustment. Approximate offset voltage.

07

2

-30.00 – 30.00

-99.99 – 99.99

-300.0 – 300.0

100% input voltage

S1 : -30.00 – 30.00mV

S2 : -99.99 – 99.99mV

S3 : -300.0 – 300.0mV

Used when adjusting the sensor sensitivity with an actual load.

Set ITEM 06 before 07.

08

2

10.0 – 100.0

Load ratio (%)

Used when adjusting the sensor sensitivity with an actual load.

100.0

09

2

-999.9 – 999.9

Tare adjustment (%)

0.0

10

N/A

-15.0 – 115.0

Input indicated in % (of the range set in ITEM 05/06/07)

----

11

2

-99.99 – 99.99

Zero adjustment (%) ( ne adj. of the value set in ITEM 05/06/07)

0.00

12

2

0.000 – 9.999

Gain adjustment ( ne adj. of the value set in ITEM 05/06/07)

1.000

13

2

0, 1, 2, 3, 4

Moving average (200 msec./sampling)

0: No

1: 4 samples

2: 8 samples

3: 16 samples

4: 32 samples

0

14

2

0, 1, 2, 3

Contact input function

0 : Tare adjustment

1 : Peak hold

2 : Valley hold

3 : Sample hold

0

15

2

10 – 99

Power ON-delay time (seconds)

10

16

2

0, 1 – 60

Power-saving mode

0 : Continuous display

1 – 60 : Time before display turned off (minutes)

10

17

18

2

2

-9999 – 9999

-9999 – 9999

BCD

-1000

1000

17

18

2

2

-7FFF – 7FFF

-7FFF – 7FFF

Binary

-7FFF

7FFF