MODEL: 73VR1100

73VR1100 SPECIFICATIONS

ES-7399 Rev.24 Page 2/18

https://www.m-system.co.jp/

Capacity: 256 MB through 1 GB

Part No.: 81.27L20.TB47C (256 MB)

81.29910.TB37C (512 MB)

81.29920.TB37C (1 GB)

(AP-CFxxxxE3ER-ETNDNR, AP-CFxxxxE3ER-ETNDNRK ...

discontinued)

• SD Card (Compatible with 73VR1100 Ver.5.03.xx or later)

Manufacturer: Hagiwara Solutions

Model No.: NSD6-004GH (B21SEI

(NSDA-004GT, NSDA-004GL ... discontinued)

SD/CF Conversion Adapter is required to use SD card. There

are some restrictions on using SD card. For details, refer to

the instruction manual.

• SD/CF Conversion Adapter (operation confirmed):

DeLOCK adaptor CF II to SDHC,SDXC

Model: 61796 (operation has been confirmed with the

adapter purchased in the year of 2016.)

62637 (operation has been confirmed with the

adapter purchased in the year of 2018.)

Note: Refer to the data sheets of the respective models.

PACKAGE INCLUDES...

• 73VR Application Software CD (model: 73VRPAC2)

• Mounting brackets (two)

(/HA: Not included for desktop type)

GENERAL SPECIFICATIONS

Construction: Panel mount type or desktop type

Degree of protection: IP65; applicable to the front panel of

the recorder with single mounting according to the specified

panel cutout (/HA: Desktop type cannot be mounted on a

panel surface)

■ CONNECTION

Power input, alarm output, RUN contact output: M3

separable screw terminal (torque 0.5 N·m)

Screw terminal: Nickel-plated steel (standard) or stainless

steel

Ethernet: RJ-45 Modular Jack

RS-485: Euro type connector terminal

Transmission media: Shielded twisted-pair cable (CPEV-S

0.9 dia.)

for both stranded and single core wires. stripped length 7

mm. Use pin terminals with stranded wires.

■ MATERIALS

Enclosure: Steel

Bezel: Flame-resistant resin (black)

Front filter: Transparent resin

Isolation: Alarm output to RUN output to power to Ethernet

to FG or RS-485

■ INDICATORS

RUN output indicator LED: Green light turns on in normal

conditions; off in an abnormality.

Power indicator LED: Green light turns on when the power is

supplied.

■ INTERFACE

Ethernet: 10BASE-T / 100BASE-TX automatically switched;

Conforms to IEEE 802 (10BASE-T) or IEEE 802.3 (100BASE-

TX)

IP address: 192.168.0.1 (factory default setting)

Subnet mask: 255.255.255.0 (factory default setting)

Default gateway: None (factory default setting)

CF Card slot: Type I; for use with the cards’ operating

voltage 3.3 V

USB: Conforms to Version 1.1

■ DISPLAY

Display device: 5.5-inch TFT LCD

Display colors: 256

Resolution: 320 × 240 pixels

Pixel pitch: 0.12 × 0.35 mm

Note: The backlight can be replaced in M-System factory.

The LCD must be replaced at the same time.

■ ALARM / RUN OUTPUT

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

(For desktop type EU conformity: < 50 V AC)

30 V DC @ 0.5 A (resistive load)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

External protection is recommended when driving an

inductive load.

RUN output contact: ON in normal conditions; OFF in errors

(CPU error, application errors)

Alarm output contact: Specified in the application software

EXTERNAL INTERFACE

■ Modbus RTU

Configuration: Half-duplex, asynchronous, no procedure

Standard: Conforms to TIA/EIA RS-485-A

Max. transmission distance: 500 meters

Transfer rate: 38400 bps

Data bit: 8

Parity bit: Odd

Stop bit: 1

Max. node number: 15 (except the master)

Transmission media:

Shielded twisted-pair cable (CPEV-S φ0.9)

Terminating resistor: incorporated