E5CC/E5EC-800

27

Operation

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

25

0

C

25

0

l.adj

ins

0.0

c-p

8.0

c-i

233

c-d

40

M

M

M

p

8.0

i

233

d

40

c-db

0.0

of-r

50.0

hys

1.0

chys

1.0

pmov

0

oapt

0

icpt

1

wtpt

off

pfpt

off

M

chgp

off

M

M

sprt

off

ol-h

100.0

ol-l

0.0

at

off

cmwt

off

ct1

0.0

M

hb1

0.0

lcr1

0

hs1

50.0

sp-0

0

sp-1

0

sp-2

0

sp-3

0

sp-4

0

sp-5

0

sp-6

0

sp-7

0

M

sp-3

0

r-s

run

al-1

0

al1h

0

al1l

0

al-2

0

al2h

0

al2l

0

M

o

0.0

c-o

0.0

25

0

a-m

m-sp

0

ct-1

0.0

lcr1

0.0

PID

Control

only

Press the

for at least 1 s. *1

Press the

O

Key or the

S

Key for at least

1 s. *1

Operation Level

Power ON

Starting in manual mode.

Adjustment Level

Press the

Press the

PV/MV

Starting in

automatic

mode.

Adjustment Level Display

Displayed only once when

entering adjustment level.

Manual Control Level

Press the

Press the

Press the

for at least 3 s.

Press the

Proportional Band

(Cooling)

Protect Level

Note: The time ta ken to move to the protect level can be

adjusted by changing the "Move to protect level time" setting.

*1. When the PF Setting parameter is set to A-M.

*2. When the PF Setting parameter is set to PFDP.

*3. These parameters are displayed regardless of

the setting of the Protocol Setting parameter.

Move to Protect Level:

Operation/Adjustment Protect:

Initial Setting/Communications Protect:

Setting Change Protect:

Displayed only when a password is set.

Restricts moving to protect level.

Restricts displaying and modifying menus in

operation, adjustment, and manual control levels.

This protect level restricts movement to the initial

setting, communicationssetting, and advanced

function setting levels.

Protects changes to setups by

operating the front panel keys.

PF Key Protect

AT Execute/Cancel

Communications

Writing

Heater Current 1

Value Monitor

Leakage Current

1 Monitor

Heater Burnout

Detection 1

HS Alarm 1

SP 0

SP 1

SP 2

SP 3

SP 4

SP 5

SP 6

SP 7

Integral Time

(Cooling)

Derivative Time

(Cooling)

Dead Band

Manual Reset Value

Clear the offset during

stabilization of P or PD

control.

Hysteresis (Heating)

Hysteresis (Cooling)

MV Upper Limit

MV Lower Limit

Hysteresis settings

Process Value

Input Shift

Process Value/Set

Point (1)

Process Value/Set

Point (2)

Auto/Manual Switch

PID 1 control only.

Added for Auto/Manual

Switch Display Addition.

Heater Current 1 Value

Monitor

Leakage Current 1

Monitor

Multi-SP Set Point

Setting

Alarm

Value 1

Alarm Value

Upper Limit 1

Alarm Value

Lower Limit 1

Alarm

Value 2

Alarm Value

Upper Limit 2

Alarm Value

Lower Limit 2

MV Monitor

(Heating)

MV Monitor

(Cooling)

Press the

Proportional Band

Integral Time

Derivative Time

PID settings

SP Ramp Set Value

RUN/STOP

Display Changed Parameters

Press the

less than 1 s.

Communications Setting Level

Note: Displayed only for models with communications. Changes

are effective after cycling power or after a software reset.

M

M

M

len

7

sbit

2

prty

even

Communications

Data Length

Communications

Stop Bits

Communications

Parity

Initial Setting Level

Press the

Press the

at least 1 s.

Other than the Auto/Manual Switch display

M

M

M

M

M

Protocol Setting

Communications

Unit No.

Communications

Baud Rate

Send Data Wait

Time

Maximum

Communications

Unit No.

Area

M

M

M

M

First Address

Upper Word

First Address

Lower Word

Receive Data

Wait Time

Upload Setting 1

M

M

M

M

Upload Setting 13

Download Setting 1

Download Setting 13

Copy

M

psel

fins

u-no

0

bps

57.6

sdwt

20

maxu

0

adrh

0

adrl

0

rwat

1000

area

0

up13

0

dn 1

0

dn13

1000

copy

off

up 1

0

M

Communications

Node Number

unit

0

Parameters

The related setting items in each level are described below. If you press the Mode Key at the last setting item, the display will return to the first

setting item in the same level.