MPC5602BAMLL4R datasheet(105/109 Pages) NXP

105 / 109 page

Document revision history

MPC5604B/C Microcontroller Data Sheet, Rev. 15

NXP Semiconductors

105

16 June 2011 Formatting and minor editorial changes throughout

Harmonized oscillator nomenclature

Removed all instances of note “All 64 LQFP information is indicative and must be

confirmed during silicon validation.”

Device comparison table: changed temperature value in footnote 2 from 105 °C to 125 °C

MPC560xB LQFP 64-pin configuration and MPC560xC LQFP 64-pin configuration:

renamed pin 6 from VPP_TEST to VSS_HV

Removed “Pin Muxing” section; added sections “Pad configuration during reset phases”,

“Voltage supply pins”, “Pad types”, “System pins,” “Functional ports”, and “Nexus 2+

pins”

Section “NVUSRO register”: edited content to separate configuration into electrical

parameters and digital functionality; updated footnote describing default value of ‘1’ in

field descriptions NVUSRO[PAD3V5V] and NVUSRO[OSCILLATOR_MARGIN]

Added section “NVUSRO[WATCHDOG_EN] field description”

Recommended operating conditions (3.3 V) and Recommended operating conditions

(5.0 V): updated conditions for ambient and junction temperature characteristics

I/O input DC electrical characteristics: updated ILKG characteristics

Section “I/O pad current specification”: removed content referencing the IDYNSEG

maximum value

I/O consumption: replaced instances of “Root medium square” with “Root mean square”

I/O weight: replaced instances of bit “SRE” with “SRC”; added pads PH[9] and PH[10];

added supply segments; removed weight values in 64-pin LQFP for pads that do not

exist in that package

Reset electrical characteristics: updated parameter classification for |IWPU|

Updated Voltage regulator electrical characteristics

Section “Low voltage detector electrical characteristics”: changed title (was “Voltage

monitor electrical characteristics”); added event status flag names found in RGM

chapter of device reference manual to POR module and LVD descriptions; replaced

instances of “Low voltage monitor” with “Low voltage detector”; updated values for

VLVDLVBKPL and VLVDLVCORL; replaced “LVD_DIGBKP” with “LVDLVBKP” in note

Updated section “Power consumption”

Fast external crystal oscillator (4 to 16 MHz) electrical characteristics: updated parameter

classification for VFXOSCOP

Crystal oscillator and resonator connection scheme: added footnote about possibility of

adding a series resistor

Slow external crystal oscillator (32 kHz) electrical characteristics: updated footnote 1

FMPLL electrical characteristics: added short term jitter characteristics; inserted “—” in

empty min value cell of tlock row

Section “Input impedance and ADC accuracy”: changed “VA/VA2” to “VA2/VA” in

Equation 11

ADC input leakage current: updated ILKG characteristics

ADC conversion characteristics: updated symbols

On-chip peripherals current consumption: changed “supply current on “VDD_HV_ADC” to

“supply current on” VDD_HV” in IDD_HV(FLASH) row; updated IDD_HV(PLL) value—was

3* fperiph, is 30 * fperiph; updated footnotes

DSPI characteristics: added rows tPCSC and tPASC

Added DSPI PCS strobe (PCSS) timing diagram

Table 49. Revision history (continued)

Revision

Date

Description of Changes

MPC5602BAMLL4R 数据表(PDF) 105 Page - NXP Semiconductors

MPC5602BAMLL4R 数据表(HTML) 105 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载