TL431IPG datasheet(3/22 Pages) ONSEMI

3 / 22 page

TL431A, B Series, NCV431A, B Series, SCV431A

www.onsemi.com

THERMAL CHARACTERISTICS

Characteristic

Symbol

D, LP Suffix

Package

P Suffix

Package

DM Suffix

Package

Unit

Thermal Resistance, Junction−to−Ambient

RqJA

178

114

240

°C/W

Thermal Resistance, Junction−to−Case

RqJC

−

°C/W

ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)

Characteristic

Symbol

TL431I

TL431C

Unit

Min

Typ

Max

Min

Typ

Max

Reference Input Voltage (Figure 1)

VKA = Vref, IK = 10 mA

TA = 25°C

TA = Tlow to Thigh (Note 2)

Vref

2.44

2.41

2.495

−

2.55

2.58

2.44

2.423

2.495

−

2.55

2.567

Reference Input Voltage Deviation Over

Temperature Range (Figure 1, Notes 3, 4)

VKA= Vref, IK = 10 mA

DVref

−

7.0

−

3.0

Ratio of Change in Reference Input Voltage to Change

in Cathode to Anode Voltage

IK = 10 mA (Figure 2),

DVKA = 10 V to Vref

DVKA = 36 V to 10 V

DVref

DVKA

−

−1.4

−1.0

−2.7

−2.0

−

−1.4

−1.0

−2.7

−2.0

mV/V

Reference Input Current (Figure 2)

IK = 10 mA, R1 = 10 k, R2 = ∞

TA = 25°C

TA = Tlow to Thigh (Note 2)

Iref

−

1.8

−

4.0

6.5

−

1.8

−

4.0

5.2

Reference Input Current Deviation Over

Temperature Range (Figure 2, Note 3)

IK = 10 mA, R1 = 10 k, R2 = ∞

DIref

−

0.8

2.5

−

0.4

1.2

Minimum Cathode Current For Regulation

VKA = Vref (Figure 1)

Imin

−

0.5

1.0

−

0.5

1.0

Off−State Cathode Current (Figure 3)

VKA = 36 V, Vref = 0 V

Ioff

−

1000

−

1000

Dynamic Impedance (Figure 1, Note 5)

VKA = Vref, DIK = 1.0 mA to 100 mA, f ≤ 1.0 kHz

|ZKA|

−

0.22

0.5

−

0.22

0.5

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

2. Tlow = −40°C for TL431AIP TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431AIDM, TL431IDM, TL431BIDM;

=0°C for TL431ACP, TL431ACLP, TL431CP, TL431CLP, TL431CD, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM,

TL431ACDM, TL431BCDM

Thigh = +85°C for TL431AIP, TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431IDM, TL431AIDM, TL431BIDM

= +70°C for TL431ACP, TL431ACLP, TL431CP, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM, TL431ACDM,

TL431BCDM

3. Guaranteed by design.

4. The deviation parameter DVref is defined as the difference between the maximum and minimum values obtained over the full operating

ambient temperature range that applies.

DVref = Vref max

-Vref min

DTA = T2 - T1

Ambient Temperature

Vref min

Vref max

The average temperature coefficient of the reference input voltage, aVref is defined as:

Vref

ppm

D Vref

Vref @25_C

X106

D TA

D Vref x106

D TA (Vref @25_C)

aVref can be positive or negative depending on whether Vref Min or Vref Max occurs at the lower ambient temperature. (Refer to Figure 6.)

Example : DVref + 8.0 mV and slope is positive,

Vref @25_C + 2.495 V,DTA + 70_C

a Vref +

0.008 x 106

70 (2.495) +

45.8 ppm _C

5. The dynamic impedance ZKA is defined as: |ZKA| +

D VKA

D IK

. When the device is programmed with two external resistors, R1 and R2,

(refer to Figure 2) the total dynamic impedance of the circuit is defined as: |ZKA | [ |ZKA| 1 )

TL431IPG 数据表(PDF) 3 Page - ON Semiconductor

TL431IPG 数据表(HTML) 3 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

数据表下载

链接网址

TL431IPG 数据表(PDF) 3 Page - ON Semiconductor

TL431IPG 数据表(HTML) 3 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

数据表 下载

链接网址

数据表下载