M28W320CB datasheet(7/42 Pages) STMICROELECTRONICS

7 / 42 page

7/42

M28W320CT, M28W320CB

DEVICE OPERATIONS

Four control pins rule the hardware access to the

Flash memory: E, G, W, RP. The following opera-

tions can be performed using the appropriate bus

cycles: Read, Write the Command of an Instruc-

tion, Output Disable, Stand-by, Reset (see Table

5).

Read. Read operations are used to output the

contents of the Memory Array, the Electronic Sig-

nature, the Status Register and the CFI. Both Chip

Enable (E) and Output Enable (G) must be at VIL

in order to perform the read operation. The Chip

Enable input should be used to enable the device.

Output Enable should be used to gate data onto

the output independently of the device selection.

The data read depend on the previous command

written to the memory (see instructions RD, RSIG,

RSR, RCFI). Read Array is the default state of the

device when exiting reset or after power-up.

Write. Write operations are used to give Com-

mands to the memory or to latch Input Data to be

programmed. A write operation is initiated when

Chip Enable E and Write Enable W are at VIL with

Output Enable G at VIH. Commands, Input Data

and Addresses are latched on the rising edge of W

or E, whichever occur first.

Output Disable. The data outputs are high im-

pedance when the Output Enable G is at VIH.

Stand-by. Stand-by disables most of the internal

circuitry allowing a substantial reduction of the cur-

rent consumption. The memory is in stand-by

when Chip Enable E is at VIH and the device is in

read mode. The power consumption is reduced to

the stand-by level and the outputs are set to high

impedance, independently from the Output Enable

G or Write Enable W inputs. If E switches to VIH

during program or erase operation, the device en-

ters in stand-by when finished.

Reset. During Reset mode all internal circuits are

switched off, the memory is deselected and the

outputs are put in high impedance. The memory is

in Reset mode when RP is at VIL. The power con-

sumption is reduced to the stand-by level, inde-

pendently from the Chip Enable E, Out-put Enable

G or Write Enable W inputs. If RP is pulled to VSS

during a Program or Erase, this operation is abort-

ed and the memory content is no longer valid as it

has been compromised by the aborted operation.

Table 5. User Bus Operations (1)

Note: 1. X = VIL or VIH,VPPH = 12V ± 5%.

Table 6. Read Electronic Signature (RSIG Instruction)

Operation

VPP

DQ0-DQ15

Read

VIL

VIH

Don’t Care

Data Output

Write

VIL

VIH

VIL

VIH

VDD or VPPH

Data Input

Output Disable

VIL

VIH

Don’t Care

Hi-Z

Stand-by

VIH

Don’t Care

Hi-Z

Reset

VIL

Don’t Care

Hi-Z

Code

Device

A2-A7

A8-A11

A12-A20

DQ0-DQ7

DQ8-DQ15

Manufact.

Code

VIL

VIH

VIL

Don’t Care

20h

00h

Device

Code

M28W320CT

VIL

VIH

VIL

Don’t Care

BAh

88h

M28W320CB

VIL

VIH

VIL

Don’t Care

BBh

88h

M28W320CB 数据表(PDF) 7 Page - STMicroelectronics

M28W320CB 数据表(HTML) 7 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载

链接网址

M28W320CB 数据表(PDF) 7 Page - STMicroelectronics

M28W320CB 数据表(HTML) 7 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表 下载

链接网址

数据表下载