P87LPC767FD datasheet(12/60 Pages) PHILIPS

12 / 60 page

Philips Semiconductors

Product data

87LPC767

Low power, low price, low pin count (20 pin)

microcontroller with 4-kbyte OTP and 8-bit A/D converter

2001 Aug 07

ADCON

Address: C0h

Bit addressable

Reset Value: 00h

BIT

SYMBOL

FUNCTION

ADCON.7

ENADC

When ENADC = 1, the A/D is enabled and conversions may take place. Must be set 10

microseconds before a conversion is started. ENADC cannot be cleared while ADCS or ADCI

are 1.

ADCON.6

Reserved for future use. Should not be set to 1 by user programs.

ADCON.5

Reserved for future use. Should not be set to 1 by user programs.

ADCON.4

ADCI

A/D conversion complete/interrupt flag. This flag is set when an A/D conversion is completed.

This bit will cause a hardware interrupt if enabled and of sufficient priority. Must be cleared by

software.

ADCON.3

ADCS

A/D start. Setting this bit by software starts the conversion of the selected A/D input. ADCS

remains set while the A/D conversion is in progress and is cleared automatically upon

completion. While ADCS or ADCI are one, new start commands are ignored.

ADCI, ADCS

A/D Status

0 0

A/D not busy, a conversion can be started.

0 1

A/D busy, the start of a new conversion is blocked.

1 0

An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion.

1 1

An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion. This

state exists for one machine cycle as an A/D conversion is completed.

ADCON.2

RCCLK

When RCCLK = 0, the CPU clock is used as the A/D clock. When RCCLK = 1, the internal RC

oscillator is used as the A/D clock. This bit is writable while ADCS and ADCI are 0.

ADCON.1, 0

AADR1,0

Along with AADR0, selects the A/D channel to be converted. These bits can only be written

while ADCS and ADCI are 0.

AADR1, AADR0

A/D Input Selected

0 0

AD0 (P0.3).

0 1

AD1 (P0.4).

1 0

AD2 (P0.5).

1 1

AD3 (P0.6).

ENADC

ADCI

ADCS

RCCLK

AADR1

AADR0

SU01354

Figure 2. A/D Control Register (ADCON)

A/D Timing

The A/D may be clocked in one of two ways. The default is to use

the CPU clock as the A/D clock source. When used in this manner,

the A/D completes a conversion in 31 machine cycles. The A/D may

be operated up to the maximum CPU clock rate of 20 MHz, giving a

conversion time of 9.3

µs. The formula for calculating A/D

conversion time when the CPU clock runs the A/D is: 186

µs / CPU

clock rate (in MHz). To obtain accurate A/D conversion results, the

CPU clock must be at least 1 MHz.

The A/D may also be clocked by the on-chip RC oscillator, even if

the RC oscillator is not used as the CPU clock. This is accomplished

by setting the RCCLK bit in ADCON. This arrangement has several

advantages. First, the A/D conversion time is faster at lower CPU

clock rates. Also, the CPU may be run at speeds below 1 MHz

without affecting A/D accuracy. Finally, the Power Down mode may

be used to completely shut down the CPU and its oscillator, along

with other peripheral functions, in order to obtain the best possible

A/D accuracy. This should not be used if the MCU uses an external

clock source greater than 4 MHz.

When the A/D is operated from the RCCLK while the CPU is running

from another clock source, 3 or 4 machine cycles are used to

synchronize A/D operation. The time can range from a minimum of 3

machine cycles (at the CPU clock rate) + 108 RC clocks to a

maximum of 4 machine cycles (at the CPU clock rate) + 112 RC

clocks.

Example A/D conversion times at various CPU clock rates are

shown in Table 1. In Table 1, maximum times for RCCLK = 1 use an

RC clock frequency of 4.5 MHz (6 MHz - 25%). Minimum times for

RCCLK = 1 use an RC clock frequency of 7.5 MHz (6 MHz + 25%).

Nominal time assume an ideal RC clock frequency of 6 MHz and an

average of 3.5 machine cycles at the CPU clock rate.

P87LPC767FD 数据表(PDF) 12 Page - NXP Semiconductors

P87LPC767FD 数据表(HTML) 12 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表下载