MPC8541ECVTAPF datasheet(62/84 Pages) FREESCALE

62 / 84 page

MPC8541E PowerQUICC™ III Integrated Communications Processor Hardware Specifications, Rev. 4

Freescale Semiconductor

Package and Pin Listings

PB[18:31]

P7, P6, P5, P4, P3, P2, P1, R1, R2, R3, R4, R5, R6,

I/0

OVDD

PC[0, 1, 4-29]

R8, R9, T9, T6, T5, T4, T1, U1, U2, U3, U4, U7, U8,

U9, U10, V9, V6, V5, V4, V3, V2, V1, W1, W2, W3,

W6, W7, W8

I/0

OVDD

PD[7, 14-25, 29-31]

Y4, AA2, AA1, AB1, AB2, AB3, AB5, AB6, AC7, AC4,

AC3, AC2, AC1, AD6, AE3, AE2

I/0

OVDD

Notes:

1. All multiplexed signals are listed only once and do not re-occur. For example, LCS5/DMA_REQ2 is listed only once in the

Local Bus Controller Interface section, and is not mentioned in the DMA section even though the pin also functions as

DMA_REQ2.

2. Recommend a weak pull-up resistor (2–10 k

Ω) be placed on this pin to OV

DD.

3. This pin must always be pulled down to GND.

4. This pin is an open drain signal.

5. This pin is a reset configuration pin. It has a weak internal pull-up P-FET which is enabled only when the MPC8541E is in the

reset state. This pull-up is designed such that it can be overpowered by an external 4.7-k

Ω pull-down resistor. If an external

device connected to this pin might pull it down during reset, then a pull-up or active driver is needed if the signal is intended

to be high during reset.

6. Treat these pins as no connects (NC) unless using debug address functionality.

7. The value of LA[28:31] during reset sets the CCB clock to SYSCLK PLL ratio. These pins require 4.7-k

Ω pull-up or pull-down

resistors. See Section 15.2, “Platform/System PLL Ratio.”

8. The value of LALE and LGPL2 at reset set the e500 core clock to CCB Clock PLL ratio. These pins require 4.7-k

Ω pull-up or

pull-down resistors. See the Section 15.3, “e500 Core PLL Ratio.”

9. Functionally, this pin is an output, but structurally it is an I/O because it either samples configuration input during reset or

because it has other manufacturing test functions. This pin will therefore be described as an I/O for boundary scan.

10.This pin functionally requires a pull-up resistor, but during reset it is a configuration input that controls 32- vs. 64-bit PCI

operation. Therefore, it must be actively driven low during reset by reset logic if the device is to be configured to be a 64-bit

PCI device. Refer to the PCI Specification.

11.This output is actively driven during reset rather than being three-stated during reset.

12.These JTAG pins have weak internal pull-up P-FETs that are always enabled.

13.These pins are connected to the VDD/GND planes internally and may be used by the core power supply to improve tracking

and regulation.

14.Internal thermally sensitive resistor.

15.No connections should be made to these pins.

16.These pins are not connected for any functional use.

17.PCI specifications recommend that a weak pull-up resistor (2–10 k

Ω) be placed on the higher order pins to OV

DD when

using 64-bit buffer mode (pins PCI_AD[63:32] and PCI2_C_BE[7:4]).

18. If this pin is connected to a device that pulls down during reset, an external pull-up is required to that is strong enough to pull

this signal to a logic 1 during reset.

19. Recommend a pull-up resistor (~1 k

Ω) be placed on this pin to OV

DD.

20. These are test signals for factory use only and must be pulled up (100

Ω το 1kΩ) to OV

DD for normal machine operation.

21. If this signal is used as both an input and an output, a weak pull-up (~

10kΩ) is required on this pin.

22. MSYNC_IN and MSYNC_OUT should be connected together for proper operation.

Table 43. MPC8541E Pinout Listing (continued)

Signal

Package Pin Number

Pin Type

Power

Supply

Notes

MPC8541ECVTAPF 数据表(PDF) 62 Page - Freescale Semiconductor, Inc

MPC8541ECVTAPF 数据表(HTML) 62 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表下载

链接网址

MPC8541ECVTAPF 数据表(PDF) 62 Page - Freescale Semiconductor, Inc

MPC8541ECVTAPF 数据表(HTML) 62 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表 下载

链接网址

数据表下载