MCP3201_07 datasheet(15/28 Pages) MICROCHIP

15 / 28 page

DS21290D-page 15

MCP3201

6.0

APPLICATIONS INFORMATION

6.1

Using the MCP3201 with

Microcontroller SPI Ports

With most microcontroller SPI ports, it is required to

clock out eight bits at a time. If this is the case, it will be

necessary to provide more clocks than are required for

the MCP3201. As an example, Figure 6-1 and

Figure 6-2 show how the MCP3201 can be interfaced

to a microcontroller with a standard SPI port. Since the

MCP3201 always clocks data out on the falling edge of

clock, the MCU SPI port must be configured to match

this operation. SPI Mode 0,0 (clock idles low) and SPI

Mode 1,1 (clock idles high) are both compatible with

the MCP3201. Figure 6-1 depicts the operation shown

in SPI Mode 0,0, which requires that the CLK from the

microcontroller idles in the ‘low’ state. As shown in the

diagram, the MSB is clocked out of the A/D Converter

on the falling edge of the third clock pulse. After the first

eight clocks have been sent to the device, the micro-

controller’s receive buffer will contain two unknown bits

(the output is at high impedance for the first two

clocks), the null bit and the highest order five bits of the

conversion. After the second eight clocks have been

sent to the device, the MCU receive register will contain

the lowest order seven bits and the B1 bit repeated as

the A/D Converter has begun to shift out LSB first data

with the extra clock. Typical procedure would then call

for the lower order byte of data to be shifted right by one

bit to remove the extra B1 bit. The B7 bit is then trans-

ferred from the high order byte to the lower order byte,

and then the higher order byte is shifted one bit to the

right as well. Easier manipulation of the converted data

can be obtained by using this method.

Figure 6-2 shows the same thing in SPI Mode 1,1

which requires that the clock idles in the high state. As

with mode 0,0, the A/D Converter outputs data on the

falling edge of the clock and the MCU latches data from

the A/D Converter in on the rising edge of the clock.

FIGURE 6-1:

SPI Communication using 8-bit segments (Mode 0,0: SCLK idles low).

FIGURE 6-2:

SPI Communication using 8-bit segments (Mode 1,1: SCLK idles high).

CLK

1011

1314

OUT

NULL

BIT

B11 B10

HI-Z

B11 B10 B9

MCU latches data from A/D

Data is clocked out of A/D

Converter on falling edges

Converter on rising edges of SCLK

45678

HI-Z

LSB first data begins

to come out

Data stored into MCU receive register

after transmission of first 8 bits

Data stored into MCU receive register

after transmission of second 8 bits

CLK

10111213

1415

OUT

NULL

BIT

B11

B10

HI-Z

B11 B10 B9

MCU latches data from A/D

Data is clocked out of A/D

Converter on falling edges

Converter on rising edges of SCLK

LSB first data begins

to come out

HI-Z

Data stored into MCU receive register

after transmission of first 8 bits

Data stored into MCU receive register

after transmission of second 8 bits

MCP3201 数据表(PDF) 15 Page - Microchip Technology

MCP3201 数据表(HTML) 15 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载

链接网址

MCP3201 数据表(PDF) 15 Page - Microchip Technology

MCP3201 数据表(HTML) 15 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表 下载

链接网址

数据表下载