TDA8714MSLASH7 datasheet(19/24 Pages) PHILIPS

19 / 24 page

1997 Oct 29

Philips Semiconductors

Product speciﬁcation

8-bit high-speed analog-to-digital converter

TDA8714

SOLDERING

Introduction

There is no soldering method that is ideal for all IC

packages. Wave soldering is often preferred when

through-hole and surface mounted components are mixed

on one printed-circuit board. However, wave soldering is

not always suitable for surface mounted ICs, or for

printed-circuits with high population densities. In these

situations reflow soldering is often used.

This text gives a very brief insight to a complex technology.

A more in-depth account of soldering ICs can be found in

our

“IC Package Databook” (order code 9398 652 90011).

Reﬂow soldering

Reflow soldering techniques are suitable for all SO and

SSOP packages.

Reflow soldering requires solder paste (a suspension of

fine solder particles, flux and binding agent) to be applied

to the printed-circuit board by screen printing, stencilling or

pressure-syringe dispensing before package placement.

Several techniques exist for reflowing; for example,

thermal conduction by heated belt. Dwell times vary

between 50 and 300 seconds depending on heating

method. Typical reflow temperatures range from

215 to 250

°C.

Preheating is necessary to dry the paste and evaporate

the binding agent. Preheating duration: 45 minutes at

°C.

Wave soldering

Wave soldering techniques can be used for all SO

packages if the following conditions are observed:

• A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave) soldering

technique should be used.

• The longitudinal axis of the package footprint must be

parallel to the solder flow.

• The package footprint must incorporate solder thieves at

the downstream end.

SSOP

Wave soldering is not recommended for SSOP packages.

This is because of the likelihood of solder bridging due to

closely-spaced leads and the possibility of incomplete

solder penetration in multi-lead devices.

If wave soldering cannot be avoided, the following

conditions must be observed:

• A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave)

soldering technique should be used.

• The longitudinal axis of the package footprint must

be parallel to the solder flow and must incorporate

solder thieves at the downstream end.

Even with these conditions, only consider wave

soldering SSOP packages that have a body width of

4.4 mm, that is SSOP16 (SOT369-1) or

SSOP20 (SOT266-1).

METHOD (SO AND SSOP)

During placement and before soldering, the package must

be fixed with a droplet of adhesive. The adhesive can be

applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the

adhesive is cured.

Maximum permissible solder temperature is 260

°C, and

maximum duration of package immersion in solder is

10 seconds, if cooled to less than 150

°C within

6 seconds. Typical dwell time is 4 seconds at 250

°C.

A mildly-activated flux will eliminate the need for removal

of corrosive residues in most applications.

Repairing soldered joints

Fix the component by first soldering two diagonally-

opposite end leads. Use only a low voltage soldering iron

(less than 24 V) applied to the flat part of the lead. Contact

time must be limited to 10 seconds at up to 300

°C. When

using a dedicated tool, all other leads can be soldered in

one operation within 2 to 5 seconds between

270 and 320

°C.

TDA8714M/7 数据表(PDF) 19 Page - NXP Semiconductors

TDA8714M/7 数据表(HTML) 19 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载