PIC16F-ESLASHML datasheet(140/178 Pages) MICROCHIP

140 / 178 page

PIC16F627A/628A/648A

DS40044F-page 138

17.4

DC Characteristics:

PIC16F627A/628A/648A (Industrial, Extended)

PIC16LF627A/628A/648A (Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial and

-40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC specification Table 17-2 and

Table 17-3

Param.

No.

Sym

Characteristic/Device

Min

Typ†

Max

Unit

Conditions

VIL

Input Low Voltage

D030

D031

D032

D033

I/O ports

with TTL buffer

with Schmitt Trigger input(4)

MCLR, RA4/T0CKI,OSC1

(in RC mode)

OSC1 (in HS)

OSC1 (in LP and XT)

VSS

—

0.8

0.15 VDD

0.2 VDD

0.3 VDD

0.6

VDD = 4.5V to 5.5V

otherwise

(Note1)

VIH

Input High Voltage

D040

D041

D042

D043

D043A

D043B

I/O ports

with TTL buffer

with Schmitt Trigger input(4)

MCLR RA4/T0CKI

OSC1 (XT and LP)

OSC1 (in RC mode)

OSC1 (in HS mode)

2.0V

.25 VDD + 0.8V

0.8 VDD

1.3

0.9 VDD

0.7 VDD

—

VDD

VDD = 4.5V to 5.5V

otherwise

(Note1)

D070

IPURB

PORTB weak pull-up

current

200

400

μAVDD = 5.0V, VPIN = VSS

IIL

Input Leakage Current(2), (3)

D060

D061

D063

I/O ports (Except PORTA)

PORTA(4)

RA4/T0CKI

OSC1, MCLR

—

±1.0

±0.5

±1.0

±5.0

μA

VSS

≤ VPIN ≤ VDD, pin at high-impedance

VSS

≤ VPIN ≤ VDD, pin at high-impedance

VSS

≤ VPIN ≤ VDD

VSS

≤ VPIN ≤ VDD, XT, HS and LP

oscillator configuration

VOL

Output Low Voltage

D080

I/O ports(4)

—

0.6

IOL = 8.5 mA, VDD = 4.5 V, -40

° to +85°C

IOL = 7.0 mA, VDD = 4.5 V, +85

° to

+125

°C

VOH

Output High Voltage(3)

D090

I/O ports (Except RA4(4) )VDD – 0.7

VDD – 0.7

—

IOH = -3.0 mA, VDD = 4.5 V, -40

° to +85°C

IOH = -2.5 mA, VDD = 4.5 V, +85

° to

+125

°C

D150

VOD

Open-Drain High Voltage

—

8.5*

RA4 pin PIC16F627A/628A/648A,

PIC16LF627A/628A/648A

Capacitive Loading Specs on Output Pins

D100*

D101*

COSC2

CIO

OSC2 pin

All I/O pins/OSC2 (in RC mode)

—

In XT, HS and LP modes when external

clock used to drive OSC1.

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5.0V, 25

°C unless otherwise stated. These parameters are for design guidance only and are not tested.

Note

In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. It is not recommended that the PIC16F627A/628A/648A

be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on applied voltage level. The specified levels represent normal

operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as coming out of the pin.

Includes OSC1 and OSC2 when configured as I/O pins, CLKIN or CLKOUT.

PIC16F-E/ML 数据表(PDF) 140 Page - Microchip Technology

PIC16F-E/ML 数据表(HTML) 140 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载