T48C862-R8 datasheet(68/107 Pages) ATMEL

68 / 107 page

T48C862-R8

4590B–4BMCU–02/03

General SSI Operation

The SSI is comprised essentially of an 8-bit shift register with two associated 8-bit buff-

ers – the receive buffer (SRB) for capturing the incoming serial data and a transmit

buffer (STB) for intermediate storage of data to be serially output. Both buffers are

directly accessable by software. Transferring the parallel buffer data into and out of the

shift register is controlled automatically by the SSI control, so that both single byte trans-

fers or continuous bit streams can be supported.

The SSI can generate the shift clock (SC) either from one of several on-chip clock

sources or accept an external clock. The external shift clock is output on, or applied to

the Port BP40. Selection of an external clock source is performed by the Serial Clock

Direction control bit (SCD). In the combinational modes, the required clock is selected

by the corresponding timer mode.

The SSI can operate in three data transfer modes – synchronous 8-bit shift mode, MCL

compatible 9-bit shift modes or 8-bit pseudo MCL protocol (without acknowledge-bit).

External SSI clocking is not supported in these modes. The SSI should thus generate

and has full control over the shift clock so that it can always be regarded as an MCL Bus

Master device.

All directional control of the external data port used by the SSI is handled automatically

and is dependent on the transmission direction set by the Serial Data Direction (SDD)

control bit. This control bit defines whether the SSI is currently operating in Transmit

(TX) mode or Receive (RX) mode.

Serial data is organized in 8-bit telegrams which are shifted with the most significant bit

first. In the 9-bit MCL mode, an additional acknowledge bit is appended to the end of the

telegram for handshaking purposes (see MCL protocol).

At the beginning of every telegram, the SSI control loads the transmit buffer into the shift

data is shifted into the shift register input. This incoming data is automatically loaded

into the receive buffer when the complete telegram has been received. Thus, data can

be simultaneously received and transmitted if required.

Before data can be transferred, the SSI must first be activated. This is performed by

means of the SSI reset control (SIR) bit. All further operation then depends on the data

directional mode (TX/RX) and the present status of the SSI buffer registers shown by

the Serial Interface Ready Status Flag (SRDY). This SRDY flag indicates the

(empty/full) status of either the transmit buffer (in TX mode), or the receive buffer (in RX

mode). The control logic ensures that data shifting is temporarily halted at any time, if

the appropriate receive/transmit buffer is not ready (SRDY = 0). The SRDY status will

then automatically be set back to ‘1’ and data shifting resumed as soon as the applica-

tion software loads the new data into the transmit register (in TX mode) or frees the shift

A further activity status (ACT) bit indicates the present status of the serial communica-

tion. The ACT bit remains high for the duration of the serial telegram or if MCL stop or

start conditions are currently being generated. Both the current SRDY and ACT status

can be read in the SSI status register. To deactivate the SSI, the SIR bit must be set

high.

T48C862-R8 数据表(PDF) 68 Page - ATMEL Corporation

T48C862-R8 数据表(HTML) 68 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载