ST7LITE2_06 datasheet(122/133 Pages) STMICROELECTRONICS

122 / 133 page

ST7LITE2

122/133

15 DEVICE CONFIGURATION

Each device is available for production in user pro-

grammable versions (FLASH) as well as in factory

coded versions (FASTROM).

ST7FLITE2

devices

are

FLASH

versions.

ST7PLITE2 devices are Factory Advanced Serv-

ice Technique ROM (FASTROM) versions: they

are factory programmed FLASH devices.

ST7FLITE2 devices are shipped to customers with

a default program memory content (FFh), while

FASTROM factory coded parts contain the code

supplied by the customer. This implies that FLASH

devices have to be configured by the customer us-

ing the Option Bytes while the FASTROM devices

are factory configured.

15.1 OPTION BYTES

The two option bytes allow the hardware configu-

ration of the microcontroller to be selected.

The option bytes can be accessed only in pro-

gramming mode (for example using a standard

ST7 programming tool).

OPTION BYTE 0

OPT7 = Reserved, must always be 1.

OPT6:4 = OSCRANGE[2:0] Oscillator range

When the internal RC oscillator is not selected

(Option OSC=1), these option bits select the range

of the resonator oscillator current source or the ex-

ternal clock source.

Note: When the internal RC oscillator is selected,

the OSCRANGE option bits must be kept at their

default value in order to select the 256 clock cycle

delay (see Section 7.5).

OPT3:2 = SEC[1:0] Sector 0 size definition

These option bits indicate the size of sector 0 ac-

cording to the following table.

OPT1 = FMP_R Read-out protection

Readout protection, when selected provides a pro-

tection against program memory content extrac-

tion and against write access to Flash memory.

Erasing the option bytes when the FMP_R option

is selected will cause the whole memory to be

erased first and the device can be reprogrammed.

Refer to the ST7 Flash Programming Reference

Manual and section 4.5 on page 14 for more de-

tails

0: Read-out protection off

1: Read-out protection on

OPT0 = FMP_W FLASH write protection

This option indicates if the FLASH program mem-

ory is write protected.

Warning: When this option is selected, the pro-

gram memory (and the option bit itself) can never

be erased or programmed again.

0: Write protection off

1: Write protection on

OSCRANGE

Typ.

frequency

range with

Resonator

1~2MHz

2~4MHz

4~8MHz

8~16MHz

VLP 32.768kHz

External

Clock source:

CLKIN

on OSC1

on PB4

Reserved

Sector 0 Size

SEC1

SEC0

0.5k

OSCRANGE

OPTION BYTE 0

OPTION BYTE 1

Res.

OSCRANGE

2:0

SEC1 SEC0

FMP

PLL

x4x8

PLL

OFF

PLL32

OFF

OSC LVD1 LVD0

WDG

HALT

Default

Value

1111

0111

ST7LITE2 数据表(PDF) 122 Page - STMicroelectronics

ST7LITE2 数据表(HTML) 122 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7LITE2 数据表(PDF) 122 Page - STMicroelectronics

ST7LITE2 数据表(HTML) 122 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载