7 Specifications

7.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1) (2) (3)

MIN

MAX

UNIT

VDD

Supply voltage

–0.5

6

V

VSEL or VEN

Logic control input pin voltage (EN, A0, A1, A2)

–0.5

6

VS or VD

Source or drain voltage (Sx, D)

–0.5

VDD+0.5

ISEL or IEN

Logic control input pin current (EN, A0, A1, A2)

–30

30

mA

IS or ID (CONT)

Continuous current through switch (Sx, D pins) –40°C to +85°C

–50

50

IS or ID (CONT)

Continuous current through switch (Sx, D pins) –40°C to +125°C

–25

25

IGND

Continuous current through GND

–100

100

Ptot

Total power dissipation(4)

500

mW

Tstg

Storage temperature

–65

150

°C

TJ

Junction temperature

150

(1)

Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute maximum ratings do not imply

functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.

If briefly operating outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not

sustain damage, but it may not be fully functional. Operating the device in this manner may affect device reliability, functionality,

performance, and shorten the device lifetime.

(2)

The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.

(3)

All voltages are with respect to ground, unless otherwise specified.

(4)

For TSSOP package: Ptot derates linearily above TA = 80°C by 7.2mW/°C.

For SOT-23-THIN package: Ptot derates linearily above TA = 66°C by 6mW/°C.

For BQB package: Ptot derates linearily above TA = 102°C by 10.6mW/°C.

7.2 ESD Ratings

VALUE

UNIT

V(ESD)

Electrostatic discharge

Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1)

±2000

V

Charged device model (CDM), per JEDEC specification JESD22-C101

or ANSI/ESDA/JEDEC JS-002, all pins(2)

±750

(1)

JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2)

JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)

MIN NOM

MAX

UNIT

VDD

Supply voltage

1.62

5.5

V

VS or VD

Signal path input/output voltage (source or drain pin) (Sx, D)

0

VDD

V

VSEL or VEN

Logic control input pin voltage (EN, A0, A1, A2)

0

5.5

V

IS or ID (CONT)

Continuous current through switch (Sx, D pins) –40°C to +85°C

–50

50

mA

IS or ID (CONT)

Continuous current through switch (Sx, D pins) –40°C to +125°C

–25

25

mA

IOK

Current per input into source or drain pins when singal voltage exceeds

recommended operating voltage (1)

–50

50

mA

IINJ

Injected current into single off switch input

–50

50

mA

IINJ_ALL

Total injected current into all off switch inputs combined

–100

100

mA

TA

Ambient temperature

–40

125

°C

(1)

If source or drain voltage exceeds VDD, or goes below GND, the pin will be shunted to GND through an internal FET, the current must

be limited within the specified value. If Vsignal > VDD or if Vsignal < GND.

www.ti.com

TMUX1308, TMUX1309

SCDS426E – MARCH 2020 – REVISED OCTOBER 2022

Copyright © 2022 Texas Instruments Incorporated

Submit Document Feedback

7

Product Folder Links: TMUX1308 TMUX1309