L6256 datasheet(25/28 Pages) STMICROELECTRONICS

25 / 28 page

Operational Description

At power up, the regulator saturates the pass ele-

ment until 3.3V is reached. If the 5V supply rises

quickly, the regulator will current limit until 3.3V is

reached. The initial current limit level is about 1/3

of the full voltage current limit level, to limit power

dissipation in the pass element.

Once the 3.3V regulation level is reached, the

regulator mantains thi svoltage regardless of load

changes, even if the DOLPHIN goes into thermal

limit. Current limit provides a signal which also

causes UV and a POR to occur.

If the 5V input is shut down before the 12V supply

is removed, the pass element will drag down the

3.3V due to the internal diode. This prevents back

biasing effects from occuring in the chips pow-

ered by the regulator.

Rgate (see block diagram) is provided to desensi-

tize the pass element to layout problems.

In most applications it will not be needed.

Charge Pump

CHARGE PUMP SPECIFICATION

Parameter

Conditions

Min.

Typ.

Max.

Unit

Slew Rate

Run Mode

600

µs

RMS Current

All Conditions

400

Peak Current

All Conditions

600

APPLICATION NOTES AND REQUIREMENTS

Serial Port

GENERAL FORMAT REQUIREMENTS

1. Serial Port Packets must be sent without inter-

vening data. The dead space between data

bytes and after write packets addressed to

this chip must be observed.

2. Read: A turnaround delay of 1 cycle minimum

is expected on a read packet, between the ad-

dress byte (written) and the first data byte

read back. This is necessary only for data ad-

dressed directly to the combo, and is normally

satisfied by the processor port turnaround re-

quirements.

3. Write: Both bytes must be written to the serial

port in rapid succession, disabling interrupts

during the write period.

4. If the dead cycle between write packets to the

DOLPHIN is not observed, an error will also

occur. This is important at high data rates.

(see manufacturer data specs).

5. Read: same as 4.

THERMAL SHUTDOWN

The serial port becomes inoperative during ther-

mal shutdown. All data coming back is high. If

the chip receives data words in which all bits are

high, the chip is non-functional. This is invisible to

the processor when compared with the thermal

time constants and the detector hysteresis built

into the chip.

Bit 3 of all registers is dedicated to thermal shut-

down detection. If it is faster to check just a sin-

gle bit rather than using a full compare, bit 3 is

available in every read register.

NOTE: this was necessary in order to guarantee

that all FF’s would truly represent only a thermal

shutdown situation.

VCM DRIVER

Software must set the VCM gain to 12:1 before

enabling the VCM coil after spinup. A transient

will occur while the amplifier slews up to its bias

point. Allow a transient settle time of several mi-

croseconds before the VCM driver has settled to

its fully enabled state.

SPINDLE DRIVER

Brake/Park

The register bits have been carefully arranged to

allow the VCM software driver to run by looking

only at the VCM control register. A register brake

would normally be initiated by the spindle driver

routine, by setting the register brake bit in the Aux

Control Register. The Dolphin will then raise the

park delay bit in the VCM Control Register, which

the VCM driver can then use to indicate that a

park has commenced. Thus, there is no need for

the drivers to be directly linked through software

flags. The register brake bit function has been

changed to allow intermittent duty cycling during

start mode, to supply additional damping. There

are some restrictions on its use.

Back EMF Detection - Initialization

The back EMF detection in start differs from that

in run. When transitioning from start to run, the

first detected phase will always be the A negative

crossing.

L6256

25/28

L6256 数据表(PDF) 25 Page - STMicroelectronics

L6256 数据表(HTML) 25 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载