STE2002DIE2 datasheet(22/51 Pages) STMICROELECTRONICS

22 / 51 page

STE2002

22/51

the second is a data byte (fig 31). The Co bit is the command MSB and defines if after this command will follow

one data byte and an other command word or if will follow a stream of data (Co = 1 Command word, Co = 0

Stream of data). The D/C bit defines whether the data byte is a command or RAM data (D/C = 1 RAM Data, D/

C = 0 Command).

If Co =1 and D/C = 0 the incoming data byte is decoded as a command, and if Co =1 and D/C =1, the following

data byte will be stored in the data RAM at the location specified by the data pointer.

Every byte of a command word must be acknowledged by all addressed units.

After the last control byte, if D/C is set to a logic 1 the incoming data bytes are stored inside the STE2002 Display

RAM starting at the address specified by the data pointer. The data pointer is automatically updated after every

byte written and in the end points to the last RAM location written.

Every byte must be acknowledged by all addressed units.

Reading Mode.

If the R/W bit is set to logic 1 the chip will output data immediately after the slave address. If the D/C bit sent

during the last write access, is set to a logic 0, the byte read is the status byte.

Figure 31. Communication Protocol

SERIAL INTERFACE

The STE2002 serial Interface is a bidirectional link between the display driver and the application supervisor.

It consists of five lines: two for data signals (SDIN, SOUT), one for clock signals (SCLK), one for the peripheral

enable (SCE) and one for mode selection (SD/C).

The serial interface is active only if the SCE line is set to a logic 0. When SCE line is high the serial peripheral

power consumption is zero. While SCE pin is high the serial interface is kept in reset.

The STE2002 is always a slave on the bus and receive the communication clock on the SCLK pin from the mas-

ter.

Information are exchanged byte-wide. During data transfer, the data line is sampled on the positive SCLK edge.

SD/C line status indicates whether the byte is a command (SD/C =0) or RAM data (SD/C =1);it is read on the

eighth SCLK clock pulse during every byte transfer.

01111

A0A

STE2002 ACK

WRITE MODE

READ MODE

R/W

SLAVE ADDRESS

STE2002 ACK

COMMAND WORD

CONTROL BYTE

MSB........LSB

LAST

N> 0 BYTE

STE2002 ACK

1 DC Control Byte

DATA Byte

DC Control Byte

A 0

DATA Byte

A P

01111

A1A

STE2002 ACK

MASTER ACK

STE2002

SLAVE ADDRESS

01111

CONTROL BYTE

000000 A

STE2002DIE2 数据表(PDF) 22 Page - STMicroelectronics

STE2002DIE2 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表下载

链接网址

STE2002DIE2 数据表(PDF) 22 Page - STMicroelectronics

STE2002DIE2 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表 下载

链接网址

数据表下载