STPCI2GDY datasheet(23/111 Pages) STMICROELECTRONICS

23 / 111 page

PIN DESCRIPTION

Issue 1.0 - July 24, 2002

23/111

used to control voltages (VPP1, VPP2 and VCC)

to a PC Card socket. Also see Section 13.7.5.

GPI# General Purpose Input. This signal is

hardwired to 1.

2.2.6. LOCAL BUS

PA[24:0] Address Bus Output.

PD[15:0] Data Bus. This is the 16-bit data bus.

D[7:0] is the LSB and PD[15:8] is the MSB.

PRD#[1:0] Read Control output. These are

memory and I/O Read signals. PRD0# is used to

read the LSB and PRD1# to read the MSB.

PWR#[1:0] Write Control output. These are

memory and I/O Write signals. PWR0# is used to

write the LSB and PWR1# to write the MSB.

PRDY Data Ready input. This signal is used to

create wait states on the bus. When high, it

completes the current cycle.

FCS#[1:0]

Two Flash Memory Chip Select

outputs. These are the Programmable Chip Select

signals for Flash memory.

IOCS#[7:0] I/O Chip Select output. These are the

Programmable Chip Select signals for up to 4

external I/O devices.

PBE#[1:0] Byte Enable. These are the Byte

enables that identifies on which databus the date

is valid. PBE#[0] corresponds to PD[7:0] and

PBE#[1] corresponds to PD[15:8]. These are

normally used when 8 bit transfers are transfered

across the 16 bit bus.

IRQ_MUX#[3:0]

Multiplexed Interrupt Lines.

2.2.7. IPC

DACK_ENC[2:0] DMA Acknowledge. These are

the ISA bus DMA acknowledge signals. They are

encoded by the STPC Industrial before output and

should be decoded externally using ISACLK and

ISACLKX2 as the control strobes.

DREQ_MUX[1:0]

ISA Bus Multiplexed DMA

Request. These are the ISA bus DMA request

signals.

They

are

encoded

before

connection to the STPC Industrial using ISACLK

and ISACLKX2 as the input selection strobes.

TC ISA Terminal Count. This is the terminal count

output of the DMA controller and is connected to

the TC line of the ISA bus. It is asserted during the

last DMA transfer, when the Byte count expires.

2.2.8. IDE INTERFACE

DA[2:0] Address. These signals are connected to

DA[2:0] of IDE devices directly or through a buffer.

If the toggling of signals are to be masked during

ISA bus cycles, they can be externally ORed with

ISAOE# before being connected to the IDE

devices.

DD[15:0]

Databus. When the IDE bus is active,

they serve as IDE signals DD[11:0]. IDE devices

are connected to SA[19:8] directly and ISA bus is

connected to these pins through two LS245

transceivers.

PCS1, PCS3, SCS1, SCS3

Primary & Secondary

Chip Selects. These signals are used as the active

high primary and secondary master & slave IDE

chip select signals. These signals must be

externally NANDed with the ISAOE# signal before

driving the IDE devices to guarantee it is active

only when ISA bus is idle. In Local Bus mode, they

just need to be inverted.

DIORDY Busy/Ready. This pin serves as IDE

signal DIORDY.

PIRQ Primary Interrupt Request.

SIRQ Secondary Interrupt Request.

Interrupt request from IDE channels.

PDRQ Primary DMA Request.

SDRQ Secondary DMA Request.

DMA request from IDE channels.

PDACK# Primary DMA Acknowledge.

SDACK# Secondary DMA Acknowledge.

DMA acknowledge to IDE channels.

PDIOR#, PDIOW# Primary I/O Read & Write.

SDIOR#, SDIOW# Secondary I/O Read & Write.

Primary & Secondary channel read & write.

2.2.9. MONITOR INTERFACE

RED, GREEN, BLUE RGB Video Outputs. These

are the 3 analog colour outputs from the

RAMDACs.

These

signals

are

sensitive

interference, therefore they need to be properly

shielded.

VSYNC

Vertical Synchronisation Pulse. This is

the vertical synchronization signal from the VGA

controller.

HSYNC Horizontal Synchronisation Pulse. This is

the horizontal synchronization signal from the

VGA controller.

VREF_DAC DAC Voltage reference. This pin is

an input driving the digital to analog converters.

This allows an external voltage reference source

to be used.

STPCI2GDY 数据表(PDF) 23 Page - STMicroelectronics

STPCI2GDY 数据表(HTML) 23 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载