TNETE2004

MDIO-MANAGED QuadPHY

FOUR 10BASE-T PHYSICAL-LAYER INTERFACES

SPWS023D – OCTOBER 1996 – REVISED OCTOBER 1997

35

POST OFFICE BOX 655303

tCOLON

COL

(see Note A)

RCVP/

RCVN

NOTE A: COL low in mode 3 asserts collision.

tCOLOFF

TXEN

Figure 28. Mode 3 Collision

tCOLON

COL

(see Note A)

RCVP/

RCVN

NOTE A: COL high in mode 4 asserts collision.

tCOLOFF

TXEN

Figure 29. Mode 4 Collision

Normal power-supply voltage

5.0 V

± 5%

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power-supply current draw (see Note 2)

510 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power-supply current draw (see Note 3)

240 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

dc voltage applied to logic outputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

dc voltage applied to logic input

5.25 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

dc differential voltage at receiver pins

± 5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage range (see Note 4)

–0.5 V to 5.25 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0

°C to 95°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

2. With all PHYs transmitting and receiving (full duplex) into correctly terminated loads and inter-frame gaps of 9.6

ms

3. With all PHYs transmitting and receiving (full duplex) into correctly terminated loads and inter-frame gaps of 10 ms

4. Voltage values are with respect to GND, and all GND pins should be routed to minimize inductance to system ground.

5. 120 pin

6. 128 pin, 2.7-mm thickness