HT86B05 datasheet(43/79 Pages) HOLTEK

43 / 79 page

HT86BXX/HT86BRXX

Rev. 1.60

October 20, 2009

· Low Voltage Reset

- LVR

The microcontroller contains a low voltage reset circuit

in order to monitor the supply voltage of the device,

which is selected via a configuration option. If the supply

voltage of the device drops to within a range of

0.9V~VLVR such as might occur when changing the bat-

tery, the LVR will automatically reset the device inter-

nally. The LVR includes the following specifications: For

a valid LVR signal, a low voltage, i.e., a voltage in the

range between 0.9V~VLVR must exist for greater than the

value tLVR specified in the A.C. characteristics. If the low

voltage state does not exceed 1ms, the LVR will ignore it

and will not perform a reset function.

· Watchdog Time-out Reset during Normal Operation

The Watchdog time-out Reset during normal opera-

tion is the same as a hardware RES pin reset except

that the Watchdog time-out flag TO will be set to

²1².

· Watchdog Time-out Reset during Power Down

The Watchdog time-out Reset during Power Down is

a little different from other kinds of reset. Most of the

conditions remain unchanged except that the Pro-

gram Counter and the Stack Pointer will be cleared to

²0² and the TO flag will be set to ²1². Refer to the A.C.

Characteristics for tSST details.

Reset Initial Conditions

The different types of reset described affect the reset

flags in different ways. These flags, known as PDF and

TO are located in the status register and are controlled

by various microcontroller operations, such as the

Power Down function or Watchdog Timer. The reset

flags are shown in the table:

TO PDF

RESET Conditions

RES reset during power-on

RES or LVR reset during normal operation

WDT time-out reset during normal operation

WDT time-out reset during Power Down

Note:

²u² stands for unchanged

The following table indicates the way in which the vari-

ous components of the microcontroller are affected after

a power-on reset occurs.

Item

Condition After RESET

Program Counter

Reset to zero

Interrupts

All interrupts will be disabled

WDT

Clear after reset, WDT begins

counting

Timer

All Timer will be turned off

Prescaler

The Timer Prescaler will be

cleared

Input/Output Ports

I/O ports will be setup as inputs

Stack Pointer

Stack Pointer will point to the top

of the stack

The different kinds of resets all affect the internal regis-

ters of the microcontroller in different ways. To ensure

reliable continuation of normal program execution after

a reset occurs, it is important to know what condition the

microcontroller is in after a particular reset occurs. The

following table describes how each type of reset affects

each of the microcontroller internal registers. Note that

where more than one package type exists the table will

reflect the situation for the larger package type.

L V R

S S T T i m e - o u t

I n t e r n a l R e s e t

t R S T D

Low Voltage Reset Timing Chart

W D T T i m e - o u t

S S T T i m e - o u t

I n t e r n a l R e s e t

t R S T D

WDT Time-out Reset during Normal Operation

Timing Chart

W D T T i m e - o u t

S S T T i m e - o u t

t S S T

WDT Time-out Reset during Power Down

Timing Chart

HT86B05 数据表(PDF) 43 Page - Holtek Semiconductor Inc

HT86B05 数据表(HTML) 43 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

数据表下载

链接网址

HT86B05 数据表(PDF) 43 Page - Holtek Semiconductor Inc

HT86B05 数据表(HTML) 43 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

数据表 下载

链接网址

数据表下载