DM6580E datasheet(19/48 Pages) DAVICOM

19 / 48 page

DM562P

V.90 Integrated Data/ Fax/Voice/Speakerphone

Modem Device Single Chip with Memory Built in

Final

Version: DM562P-DS-F01

FIFO Control Register (FCR): Address 2

Reset State 00h , write only

bit7

bit6

bit5 bit4 bit3

bit2

bit1

bit0

RCVR

Trig

(MSB)

RCVR

Trig

(LSB)

DMA

Mode

TxFIFO

Reset

RxFIFO

Reset

FIFO

Enable

This is a write only register at the same location as

the IIR, which is a read only register. This register is

used to enable the FIFOs, clear the FIFOs, set the

RxFIFO trigger level, and select the type of DMA

signal.

Bit 0: FIFO Enable, This bit is always high

Bit 1: Writing a 1 to FCR1 clears all bytes in the

RxFIFO and resets the counter logic to 0.

Bit 2: Writing a 1 to FCR2 clears all bytes in the

TxFIFO and resets the counter logic to 0.

Bit 3: Setting FCR3 to 1 will cause the RXRDY and

TXRDY pins to change from mode 0 to mode

1 if FCR0 = 1.

Bit 4-5: Reserved

Bit 6-7: FCR6, FCR7 are used to set the trigger

level for the RxFIFO interrupt.

FCR7

FCR6

RxFIFO Trigger Level

Line Control Register (LCR): Address 3

Reset State 00h, Write Only

bit7

bit6

bit5 bit4 bit3 bit2

bit1

bit0

DLAB SBRK STP EPS PEN STB WLS1 WLS0

This register is available to maintain compatibility

with the standard 16550 register set, and provides

information to the internal hardware that is used to

determine the number of bits per character.

WLS1

WLS0

Word Length

5 bits

6 bits

7 bits

8 bits

Bit 0-1: WLS0-1 specifies the number of bits in each

transmitted and received serial character.

Bit 2: STB specifies the number of stop bits in each

transmitted character. If bit 2 is a logic 0, one

stop bit is generated in the transmitted data. If

bit 2 is a logic 1 when a 5-bit word length is

selected via bits 0 and 1, one and a half stops

are generated. If bit 2 is a logic 1 when either

a 6-, 7- or 8-bit word length is selected, two

stop bits are generated. The Receiver checks

the first Stop-bit only, regardless of the

number of Stop bits selected.

Bit 3: Logic 1 indicates that the PC has enabled

parity generation and checking.

Bit 4: Logic 1 indicates that the PC is requesting an

even number of logic 1s (even parity

generation) to be transmitted or checked.

Logic 0 indicates that the PC is requesting

odd parity generation and checking.

Bit 5: When bits 3, 4 and 5 are logic 1, the parity bit

transmitted and checked by the receiver

as logic 0. If bits 3 and 5 are 1 and bit 4 is

logic 0, then the parity is transmitted and

checked as logic 1.

Bit 6: This is a Break Control bit. When it is set to

logic 1, a break condition is indicated.

Bit 7: The Divisor Latch Access bit must be set to

logic 1 to access the Divisor Latches of the

baud generator during a read or write

operation. It must be set to logic 0 to access

the Receiver Buffer, the Transmitter Holding

February 02, 2004

DM6580E 数据表(PDF) 19 Page - Davicom Semiconductor, Inc.

DM6580E 数据表(HTML) 19 Page - Davicom Semiconductor, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载