MCP4901-ESLASHMS datasheet(27/50 Pages) MICROCHIP

27 / 50 page

 2010 Microchip Technology Inc.

DS22248A-page 27

MCP4901/4911/4921

6.0

TYPICAL APPLICATIONS

The MCP4901/4911/4921 family devices are general

purpose DACs intended to be used in applications

where

precision

with

low-power

and

moderate

bandwidth is required.

Applications generally suited for the devices are:

• Set Point or Offset Trimming

• Sensor Calibration

• Digitally-Controlled Multiplier/Divider

• Portable Instrumentation (Battery Powered)

• Motor Control Feedback Loop

6.1

Digital Interface

The MCP4901/4911/4921 devices utilize a 3-wire

synchronous serial protocol to transfer the DAC’s setup

and output values from the digital source. The serial

protocol can be interfaced to SPI or Microwire periph-

erals that are common on many microcontrollers,

including Microchip’s PIC® MCUs and dsPIC® DSCs.

In addition to the three serial connections (CS, SCK

and SDI), the LDAC pin synchronizes the analog output

(VOUT) with the pin event. By bringing the LDAC pin

down “low”, the DAC input code and settings in the

input register are latched into the output register, and

the analog output is updated. Figure 6-1 shows an

example of the pin connections. Note that the LDAC pin

can be tied low (VSS) to reduce the required

connections from 4 to 3 I/O pins. In this case, the DAC

output can be immediately updated when a valid

16-clock transmission has been received and CS pin

has been raised.

6.2

Power Supply Considerations

The typical application will require a bypass capacitor

in order to filter high-frequency noise. The noise can be

induced onto the power supply's traces from various

events such as digital switching or as a result of

changes on the DAC's output. The bypass capacitor

helps to minimize the effect of these noise sources.

Figure 6-1 illustrates an appropriate bypass strategy. In

this example, two bypass capacitors are used in

parallel: (a) 0.1 µF (ceramic) and (b) 10 µF (tantalum).

These capacitors should be placed as close to the

device power pin (VDD) as possible (within 4 mm).

The power source supplying these devices should be

as clean as possible. If the application circuit has

separate digital and analog power supplies, VDD and

VSS should reside on the analog plane.

FIGURE 6-1:

Typical Connection

Diagram.

6.3

Layout Considerations

Inductively-coupled AC transients and digital switching

noises can degrade the input and output signal

integrity, potentially reducing the device’s performance.

Careful board layout will minimize these effects and

increase the Signal-to-Noise Ratio (SNR). Bench test-

ing has shown that a multi-layer board utilizing a

low-inductance ground plane, isolated inputs, and

isolated outputs with proper decoupling, is critical for

best performance. Particularly harsh environments

may require shielding of critical signals.

Breadboards

and

wire-wrapped

boards

are

not

recommended if low noise is desired.

VDD

AVSS

VSS

VREF

VOUT

VREF

VOUT

SDI

CS1

SDO

SCK

LDAC

CS0

C1 = 10 µF

C2 = 0.1 µF

MCP4901-E/MS 数据表(PDF) 27 Page - Microchip Technology

MCP4901-E/MS 数据表(HTML) 27 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

数据表下载