P89LPC9331FDH datasheet(39/93 Pages) NXP

39 / 93 page

P89LPC9331_9341_9351_9361_3

Product data sheet

Rev. 03 — 2 June 2009

39 of 93

NXP Semiconductors

P89LPC9331/9341/9351/9361

8-bit microcontroller with accelerated two-clock 80C51 core

Some chip functions continue to operate and draw power during Power-down mode,

increasing the total power used during power-down. These include: Brownout detect,

watchdog timer, comparators (note that comparators can be powered down separately),

and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator

has been selected as the system clock and the RTC is enabled.

7.18.3 Total Power-down mode

This is the same as Power-down mode except that the brownout detection circuitry and

the voltage comparators are also disabled to conserve additional power. The internal RC

oscillator is disabled unless both the RC oscillator has been selected as the system clock

and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during

power-down, there will be high power consumption. Please use an external low frequency

clock to achieve low power with the RTC running during power-down.

7.19 Reset

The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,

P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external

reset input function on P1.5. When cleared, P1.5 may be used as an input pin.

Remark: During a power-up sequence, the RPE selection is overridden and this pin

always functions as a reset input. An external circuit connected to this pin should not

hold this pin LOW during a power-on sequence as this will keep the device in reset.

After power-up this pin will function as deﬁned by the RPE bit. Only a power-up reset will

temporarily override the selection deﬁned by RPE bit. Other sources of reset will not

override the RPE bit.

Note: During a power cycle, VDD must fall below VPOR before power is reapplied, in order

to ensure a power-on reset (see Table 12 “Static characteristics”).

Reset can be triggered from the following sources:

• External reset pin (during power-up or if user conﬁgured via UCFG1)

• Power-on detect

• Brownout detect

• Watchdog timer

• Software reset

• UART break character detect reset

For every reset source, there is a ﬂag in the Reset Register, RSTSRC. The user can read

this register to determine the most recent reset source. These ﬂag bits can be cleared in

software by writing a logic 0 to the corresponding bit. More than one ﬂag bit may be set:

• During a power-on reset, both POF and BOF are set but the other ﬂag bits are

cleared.

• A Watchdog reset is similar to a power-on reset, both POF and BOF are set but the

other ﬂag bits are cleared.

• For any other reset, previously set ﬂag bits that have not been cleared will remain set.

P89LPC9331FDH 数据表(PDF) 39 Page - NXP Semiconductors

P89LPC9331FDH 数据表(HTML) 39 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

数据表下载