70592C datasheet(146/314 Pages) MICROCHIP

146 / 314 page

PIC24HJXXXGPX06A/X08A/X10A

DS70592C-page 146

11.2

Open-Drain Configuration

In addition to the PORT, LAT and TRIS registers for

data control, some port pins can also be individually

configured for either digital or open-drain output. This is

controlled by the Open-Drain Control register, ODCx,

associated with each port. Setting any of the bits con-

figures the corresponding pin to act as an open-drain

output.

The open-drain feature allows the generation of

outputs higher than VDD (e.g., 5V) on any desired 5V

tolerant pins by using external pull-up resistors. The

maximum open-drain voltage allowed is the same as

the maximum VIH specification.

See the “Pin Diagrams” section for the available pins

and their functionality.

11.3

Configuring Analog Port Pins

The use of the ADxPCFGH, ADxPCFGL and TRIS

registers control the operation of the Analog-to-Digital

port pins. The port pins that are desired as analog

inputs must have their corresponding TRIS bit set

(input). If the TRIS bit is cleared (output), the digital out-

put level (VOH or VOL) is converted.

Clearing any bit in the ADxPCFGH or ADxPCFGL reg-

ister configures the corresponding bit to be an analog

pin. This is also the Reset state of any I/O pin that has

an analog (ANx) function associated with it.

When reading the PORT register, all pins configured as

analog input channels will read as cleared (a low level).

Pins configured as digital inputs will not convert an

analog input. Analog levels on any pin that is defined as

a digital input (including the ANx pins) can cause the

input buffer to consume current that exceeds the

device specifications.

11.4

I/O Port Write/Read Timing

One instruction cycle is required between a port

direction change or port write operation and a read

operation of the same port. Typically, this instruction

would be a NOP.

11.5

Input Change Notification

The input change notification function of the I/O ports

allows the PIC24HJXXXGPX06A/X08A/X10A devices

to generate interrupt requests to the processor in

response to a change-of-state on selected input pins.

This

feature

capable

detecting

input

change-of-states even in Sleep mode, when the clocks

are disabled. Depending on the device pin count, there

are up to 24 external signals (CN0 through CN23) that

can be selected (enabled) for generating an interrupt

request on a change-of-state.

There are four control registers associated with the CN

module. The CNEN1 and CNEN2 registers contain the

CN interrupt enable (CNxIE) control bits for each of the

CN input pins. Setting any of these bits enables a CN

interrupt for the corresponding pins.

Each CN pin also has a weak pull-up connected to it.

The pull-ups act as a current source that is connected

to the pin and eliminate the need for external resistors

when push button or keypad devices are connected.

The pull-ups are enabled separately using the CNPU1

and CNPU2 registers, which contain the weak pull-up

enable (CNxPUE) bits for each of the CN pins. Setting

any of the control bits enables the weak pull-ups for the

corresponding pins.

EXAMPLE 11-1:

PORT WRITE/READ EXAMPLE

Note:

In devices with two ADC modules, if the

corresponding

PCFG

bit

either

AD1PCFGH(L) and AD2PCFGH(L) is

cleared, the pin is configured as an analog

input.

Note:

The voltage on an analog input pin can be

between -0.3V to (VDD + 0.3 V).

Note:

Pull-ups on change notification pins

should always be disabled whenever the

port pin is configured as a digital output.

MOV

0xFF00, W0

; Configure PORTB<15:8> as inputs

MOV

W0, TRISBB

; and PORTB<7:0> as outputs

NOP

; Delay 1 cycle

btss

PORTB, #13

; Next Instruction

70592C 数据表(PDF) 146 Page - Microchip Technology

70592C 数据表(HTML) 146 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

70592C 数据表(PDF) 146 Page - Microchip Technology

70592C 数据表(HTML) 146 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载