UBA2015AP datasheet(25/42 Pages) PHILIPS

25 / 42 page

UBA2016A_15_15A

All information provided in this document is subject to legal disclaimers.

Objective data sheet

Rev. 1 — 20 May 2011

25 of 42

NXP Semiconductors

UBA2016A/15/15A

600 V fluorescent lamp driver

[1]

Positive and negative latch-up currents tested at Tj = 150 °C by discharging a 22 μF capacitor though a 50 Ω series resistor with a

350

μH series inductor. Latch-up current values are in accordance with the general quality specification.

Thermal characteristics

10. Characteristics

ElectroStatic Discharge (ESD)

VESD

electrostatic discharge

voltage

Human Body Model (HBM)

JEDEC Class 2 for pins: SLHB, IFB, EOL, CIFB,

CPT, IREF, VFB, CF, DIM, BOOST, PH/EN, FBPFC,

COMPPFC, AUXPFC, GPFC, VDD and GLHB

−2+2

JEDEC Class 1C for pins: GHHB, FSHB and SHHB

−1+1

Charge Device Model (CDM)

JEDEC Class 2 for pins: SHHB, FSHB, GHHB

−200

+200

JEDEC Class 3 for pins: SLHB, IFB, EOL, VFB,

IREF, CIFB, CF, CPT, DIM, BOOST, PH/EN, FBPFC,

COMPPFC, AUXPFC, GPFC, VDD, GLHB

−500

+500

Latch-up

Ilu

latch-up current

[1]

−100

+100

Table 4.

Limiting values …continued

In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages referenced to signal ground (GND

pin 15); current flow into the IC is positive.

Symbol

Parameter

Conditions

Min

Max

Unit

Table 5.

Thermal characteristics

Symbol

Parameter

Conditions

Typ

Unit

Rth(j-a)

thermal resistance from junction to

ambient

in free air; mounted on a single-sided PCB;

SO20 package

100

K/W

in free air; mounted on a single-sided PCB;

DIP20 package

K/W

Table 6.

Characteristics

Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive;

unless otherwise specified.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

High voltage

Ileak

leakage current

VFSHB =630 V;

VGHHB =630 V;

VSHHB = 630 V; VVDD =0V

μA

Start-up

Vstartup(VDD)

start-up voltage on pin VDD

11.9

12.4

12.9

Vstop(VDD)

stop voltage on pin VDD

9.6

10.0

10.4

Vhys(VDD)

hysteresis voltage on pin VDD

2.1

2.4

2.7

Istb(VDD)

standby current on pin VDD

VVDD = 11.5 V

0.20

0.24

0.28

Ipu(stb)(PH/EN)

standby pull-up current on pin PH/EN

Standby or Stop state;

VPH/EN =0.25V

7.7

10.3

μA

Vrst(VDD)

reset voltage on pin VDD

3.6

4.2

4.8

UBA2015AP 数据表(PDF) 25 Page - NXP Semiconductors

UBA2015AP 数据表(HTML) 25 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载

链接网址

UBA2015AP 数据表(PDF) 25 Page - NXP Semiconductors

UBA2015AP 数据表(HTML) 25 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表 下载

链接网址

数据表下载