ADL5363ACPZ-R7 datasheet(21/24 Pages) AD

21 / 24 page

ADL5363

Rev. 0 | Page 21 of 24

Table 7. Evaluation Board Configuration

Components

Function

Description

Default Conditions

C2, C6, C8,

C20, C21

Power supply

decoupling

Power Supply Decoupling. Nominal supply decoupling

consists of a 10 μF capacitor to ground in parallel with a

10 pF capacitor to ground positioned as close to the device

as possible.

C2 = 10 μF (size 0603),

C6, C8, C20, C21 = 10 pF (size 0402)

C1, C4, C5, Z1

RF input interface

RF Input Interface. The input channels are ac-coupled

through C1. C4 and C5 provide bypassing for the center taps

of the RF input baluns.

C1 = 1.5 pF (size 0402),

C4 = 10 pF (size 0402),

C5 = 0.01 μF (size 0402)

Z1= 12 nH (size 0402)

T1, R1, C24, C25

IF output interface

IF Output Interface. T1 is a 1:1 impedance transformer used

to provide a single-ended IF output interface. Remove R1

for balanced output operation. C24 and C25 are used to

block the dc bias at the IF ports.

T1 = TC1-1-13M+ (Mini-Circuits),

R1 = 0 Ω (size 0402),

C24, C25 = 560 pF (size 0402)

C10, C12, R4

LO interface

LO Interface. C10 and C12 provide ac coupling for the

LO1_IN and LO2_IN local oscillator inputs. LOSEL selects

the appropriate LO input for both mixer cores. R4 provides

a pull-down to ensure that LO1_IN is enabled when the

LOSEL test point is logic low. LO2_IN is enabled when

LOSEL is pulled to logic high.

C10, C12 = 22 pF (size 0402),

R4 = 10 kΩ (size 0402)

R21

PWDN interface

PWDN Interface. R21 pulls the PWDN logic low and enables

the device. The PWR_UP test point allows the PWDN

interface to be exercised using the an external logic

generator. Grounding the PWDN pin for nominal operation

is allowed. Using the PWDN pin when supply voltages

exceed 3.3 V is not allowed.

R21 = 10 kΩ (size 0402)

C22, L3, R9, R14,

R22, R23, VGS0,

VGS1

Bias control

Bias Control. R22 and R23 form a voltage divider to provide

3 V for logic control, bypassed to ground through C22.

VGS0 and VGS1 jumpers provide programmability at the

VGS0 and VGS1 pins. It is recommended to pull these two

pins to ground for nominal operation. R9 sets the bias

point for the internal LO buffers.

C22 = 1 nF (size 0402),

L3 = 0 Ω (size 0603),

R9 = 1.1 kΩ (size 0402),

R14 = 0 Ω (size 0402),

R22 = 10 kΩ (size 0402),

R23 = 15 kΩ (size 0402),

VGS0 = VGS1 = 3-pin shunt

ADL5363ACPZ-R7 数据表(PDF) 21 Page - Analog Devices

ADL5363ACPZ-R7 数据表(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载