ThunderLAN

™ TNETE110

PCI ETHERNET

™ CONTROLLER

SINGLE-CHIP 10 BASE-T

SPWS018B – MARCH 1995 - REVISED MAY 1996

7

POST OFFICE BOX 1443

Pin Functions (Continued)

PIN

TYPE†

DESCRIPTION

NAME

NO.

TYPE†

DESCRIPTION

PCI INTERFACE (CONTINUED)

PREQ

134

I/O

PCI bus request. PREQ is asserted by the TNETE110 to request control of the PCI bus. This is not a

shared signal.

PRST

129

I

PCI reset signal

PSERR

25

O/D

PCI system error. PSERR indicates parity errors or special-cycle data-parity errors.

PSTOP

23

I/O

PCI stop. PSTOP indicates the current target is requesting the master to stop the current transaction.

BIOS ROM / LED DRIVER INTERFACE

EAD7

EAD6

EAD5

EAD4

EAD3

EAD2

EAD1

EAD0

54

55

56

57

59

60

61

62

I/O

EPROM address / data. EAD[0 –7] is a multiplexed byte bus that is used to address and to read data

from an external BIOS ROM.

• On the cycle when EXLE is asserted low, EAD[0–7] is driven with the high byte of the

address.

• On the cycle when EALE is asserted low, EAD[0–7] is driven with the low byte of the

address.

• When EOE is asserted, BIOS ROM data should be placed on the bus.

These pins can be used also to drive external status LEDs. Low-current (2 – 5 mA) LEDs can be

connected directly through appropriate resistors. High-current LEDs can be driven through buffers

or from the BIOS ROM address latches.

EALE

65

O

EPROM address latch enable. EALE is driven low to latch the low (least significant) byte of the BIOS

ROM address from EAD[0 –7].

EOE

64

O

EPROM output enable. When EOE is active (low), EAD[0 –7] is 3-stated and the output of the BIOS

ROM should be placed on EAD[0 –7].

EXLE

66

O

EPROM extended address-latch enable. EXLE is driven low to latch the high (most significant) byte

of the BIOS ROM address from EAD[0 –7].

CONFIGURATION EEPROM INTERFACE

EDCLK

68

O

EEPROM data clock. EDCLK transfers serial clocked data to the 2K-bit serial EEPROMs (24C02) (see

Note 1).

EDIO

69

I/O

EEPROM data I / O. EDIO is the bidirectional serial data / address line to the 2K-bit serial EEPROM

(24C02). EDIO requires an external pullup for EEPROM operation. Tying EDIO to ground disables the

EEPROM interface and prevents autoconfiguration of the PCI configuration register.

MANAGEMENT DATA PINS

MDCLK

91

O

Management data clock. MDCLK is part of the serial management interface to physical-media

independent (PMI)/PHY chip.

MDIO

93

I/O

Management data I / O. MDIO is part of the serial management interface to PMI/PHY chip.

NETWORK INTERFACE (10 Base-T AND AUI)

ACOLN

ACOLP

111

109

A

AUI receive pair. ACOLN and ACOLP are differential line receiver inputs and connect to the receive

pair through transformer isolation, etc.

ARCVN

ARCVP

108

106

A

AUI receive pair. ARCVN and ARCVP are differential line receiver inputs and connect to the receive

pair through transformer isolation, etc.

AXMTP

AXMTN

99

100

A

AUI transmit pair. AXMTP and AXMTN are differential line transmitter outputs.

FATEST

118

A

Analog test pin. FATEST provides access to the filter of the reference PLL. This pin must be left as a

no connect.

FIREF

116

A

Current reference. FIREF is used to set a current reference for the analog circuitry.

† I = input, O = output, I / O = 3-state input / output, O / D = open-drain output, A = analog

NOTE 1: This pin should be tied to VDD with a 4.7-kW – 10-kW pullup resistor.