| 数据搜索系统,热门电子元器件搜索 |
|
RT8205CGQW 数据表(PDF) 27 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT8205CGQW 数据表(HTML) 27 Page - Richtek Technology Corporation |
|
27 / 28 page ![]() RT8205A/B/C 27 DS8205A/B/C-06 July 2012 www.richtek.com © Copyright 2012 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. Table 2. Operation Mode Truth Table Mode Condition Comment Power-UP VREGx < UVLO threshold Transitions to discharge mode after a VIN POR and after REF becomes valid. VREG5, VREG3, and REF remain active. RUN EN = high, VOUT1 or VOUT2 enabled Normal Operation. Over Voltage Protection Either output > 111% of the nominal level. LGATEx is forced high. VREG3, VREG5 active. Exited by VIN POR or by toggling EN, ENT RIPx Under Voltage Protection Either output < 70% of the nominal level after 3ms time-out expires and output is enabled Both UGATEx and LGATEx are forced low and enter discharge mode. VREG3, VREG5 active. Exited by VIN POR or by toggling EN, ENTRIPx D ischarge Either SMPS output is still high in either standby mode or shutdown mode During discharge mode, there is one path to discharge the outputs capacitor residual charge. That is output capacitor discharge to GND through an internal switch. Standby ENTRIPx < startup threshold, EN = high. VREG3, VREG5 active. Shutdown EN = low All circuitry off. Thermal Shutdown TJ > +150°C All circuitry off. Exit by VIN POR or by toggling EN, ENTRIPx. Table 3. Power-Up Sequencing EN (V) ENTRIP1 (V) ENTRIP2 (V) VREG5 VREG3 SMPS1 SMPS2 Low X X Off Off Off Off “>1V” => High Low Low On (after REF powers up) On (after REF powers up) Off Off “>1V” => High Low High On (after REF powers up) On (after REF powers up) Off On “>1V” => High High (after ENTRIP2 is high without 60us) High On (after REF powers up) On (after REF powers up) On (after SMPS2 on) On “>1V” => High High Low On (after REF powers up) On (after REF powers up) On Off “>1V” => High High High (after ENTRIP1 is high without 60us) On (after REF powers up) On (after REF powers up) ON On (after SMPS1 on) “>1V” => High High High On (after REF powers up) On (after REF powers up) On On |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |