AD9283SLASHPCB datasheet(3/12 Pages) AD

3 / 12 page

–3–

REV. B

AD9283

Test

AD9283BRS-100

AD9283BRS-80

AD9283BRS-50

Parameter

Temp

Level

Min Typ

Max

Min

Typ

Max

Min

Typ

Max

Units

DYNAMIC PERFORMANCE

Transient Response

+25

°CV

Overvoltage Recovery Time

+25

°CV

Signal-to-Noise Ratio (SNR)

(Without Harmonics)

fIN = 10.3 MHz

+25

°C

46.5

fIN = 27 MHz

+25

°C

46.5

fIN = 41 MHz

+25

°C

43.5 46.5

fIN = 76 MHz

+25

°C

46.0

Signal-to-Noise Ratio (SINAD)

(With Harmonics)

fIN = 10.3 MHz

+25

°C

43.5

46.5

fIN = 27 MHz

+25

°C

45.5

43.5

46.5

fIN = 41 MHz

+25

°C

42.5 45

fIN = 76 MHz

+25

°C

42.5

Effective Number of Bits

fIN = 10.3 MHz

+25

°C

7.3

7.5

7.6

Bits

fIN = 27 MHz

+25

°C

7.4

7.5

Bits

fIN = 41 MHz

+25

°C

7.3

7.5

Bits

fIN = 76 MHz

+25

°C

6.9

Bits

2nd Harmonic Distortion

fIN = 10.3 MHz

+25

°C

dBc

fIN = 27 MHz

+25

°C

dBc

fIN = 41 MHz

+25

°C

dBc

fIN = 76 MHz

+25

°CV

dBc

3rd Harmonic Distortion

fIN = 10.3 MHz

+25

°C

54.5

dBc

fIN = 27 MHz

+25

°C

62.5

dBc

fIN = 41 MHz

+25

°C

52.5

dBc

fIN = 76 MHz

+25

°CV

dBc

Two-Tone Intermod Distortion

(IMD)

fIN = 10.3 MHz

+25

°C

dBc

NOTES

1Gain error and gain temperature coefficient are based on the ADC only (with a fixed 1.25 V external reference).

V and tPD are measured from the 1.5 V level of the ENCODE input to the 50%/50% levels of the digital outputs swing. The digital output load during test is not to

exceed an ac load of 10 pF or a dc current of

± 40 µA.

3Power dissipation measured with encode at rated speed and a dc analog input.

4Typical thermal impedance for the RS style (SSOP) 20-lead package:

JC = 46°C/W, θCA = 80°C/W, θJA = 126°C/W.

5SNR/harmonics based on an analog input voltage of –0.7 dBFS referenced to a 1.024 V full-scale input range.

Specifications subject to change without notice.

ABSOLUTE MAXIMUM RATINGS*

VD, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4 V

Analog Inputs . . . . . . . . . . . . . . . . . . . . –0.5 V to VD + 0.5 V

Digital Inputs . . . . . . . . . . . . . . . . . . . –0.5 V to VDD + 0.5 V

VREF IN . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VD + 0.5 V

Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 20 mA

Operating Temperature . . . . . . . . . . . . . . . . –55

°C to +125°C

Storage Temperature . . . . . . . . . . . . . . . . . . –65

°C to +150°C

Maximum Junction Temperature . . . . . . . . . . . . . . . +175

°C

Maximum Case Temperature . . . . . . . . . . . . . . . . . . +150

°C

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection.

Although the AD9283 features proprietary ESD protection circuitry, permanent damage may

occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD

precautions are recommended to avoid performance degradation or loss of functionality.

ORDERING GUIDE

Temperature

Package

Model

Ranges

Descriptions

Options

AD9283BRS

-50, -80, -100 –40

°C to +85°C 20-Lead SSOP

RS-20

AD9283/PCB

+25

°C

Evaluation Board

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the

device at these or any other conditions outside of those indicated in the operation

sections of this specification is not implied. Exposure to absolute maximum

ratings for extended periods may affect device reliability.

WARNING!

ESD SENSITIVE DEVICE

AD9283/PCB 数据表(PDF) 3 Page - Analog Devices

AD9283/PCB 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载

链接网址

AD9283/PCB 数据表(PDF) 3 Page - Analog Devices

AD9283/PCB 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表 下载

链接网址

数据表下载