INTEDG datasheet(64/478 Pages) MICROCHIP

64 / 478 page

PIC16(L)F1946/47

DS41414D-page 64

 2010-2012 Microchip Technology Inc.

FIGURE 5-3:

QUARTZ CRYSTAL

OPERATION (LP, XT OR

HS MODE)

FIGURE 5-4:

CERAMIC RESONATOR

OPERATION

(XT OR HS MODE)

5.2.1.3

Oscillator Start-up Timer (OST)

If the oscillator module is configured for LP, XT or HS

modes, the Oscillator Start-up Timer (OST) counts

1024 oscillations from OSC1. This occurs following a

Power-on Reset (POR) and when the Power-up Timer

(PWRT) has expired (if configured), or a wake-up from

Sleep. During this time, the program counter does not

increment and program execution is suspended. The

OST ensures that the oscillator circuit, using a quartz

crystal resonator or ceramic resonator, has started and

is providing a stable system clock to the oscillator

module.

In order to minimize latency between external oscillator

start-up and code execution, the Two-Speed Clock

Start-up mode can be selected (see Section 5.4

“Two-Speed Clock Start-up Mode”).

5.2.1.4

4x PLL

The oscillator module contains a 4x PLL that can be

used with both external and internal clock sources to

provide a system clock source. The input frequency for

the 4x PLL must fall within specifications. See the PLL

Clock

Timing

Specifications

Section 30.0

“Electrical Specifications”.

The 4x PLL may be enabled for use by one of two

methods:

Program the PLLEN bit in Configuration Words

to a ‘1’.

Write the SPLLEN bit in the OSCCON register to

a ‘1’. If the PLLEN bit in Configuration Words is

programmed to a ‘1’, then the value of SPLLEN

is ignored.

Note 1: Quartz

crystal

characteristics

vary

according

type,

package

and

manufacturer. The user should consult the

manufacturer data sheets for specifications

and recommended application.

2: Always verify oscillator performance over

the VDD and temperature range that is

expected for the application.

3: For oscillator design assistance, reference

the following Microchip Applications Notes:

• AN826, “Crystal Oscillator Basics and

Crystal Selection for rfPIC® and PIC®

Devices” (DS00826)

• AN849, “Basic PIC® Oscillator Design”

(DS00849)

• AN943, “Practical PIC® Oscillator

Analysis and Design” (DS00943)

• AN949, “Making Your Oscillator Work”

(DS00949)

Note 1: A series resistor (RS) may be required for

quartz crystals with low drive level.

2: The value of RF varies with the Oscillator mode

selected (typically between 2 M

 to 10 M.

Quartz

RS(1)

OSC1/CLKIN

RF(2)

Sleep

To Internal

Logic

PIC® MCU

Crystal

OSC2/CLKOUT

Note 1: A series resistor (RS) may be required for

ceramic resonators with low drive level.

2: The value of RF varies with the Oscillator mode

selected (typically between 2 M

 to 10 M.

3: An additional parallel feedback resistor (RP)

may be required for proper ceramic resonator

operation.

C2 Ceramic

RS(1)

OSC1/CLKIN

RF(2)

Sleep

To Internal

Logic

PIC® MCU

RP(3)

Resonator

OSC2/CLKOUT

INTEDG 数据表(PDF) 64 Page - Microchip Technology

INTEDG 数据表(HTML) 64 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载