DSPIC33FJMC202ESS datasheet(102/330 Pages) MICROCHIP

102 / 330 page

dsPIC33FJ32MC202/204 and dsPIC33FJ16MC304

DS70283K-page 102

8.1

CPU Clocking System

The

dsPIC33FJ32MC202/204

and

dsPIC33FJ16MC304 devices provide seven system

clock options:

• Fast RC (FRC) Oscillator

• FRC Oscillator with PLL

• Primary (XT, HS or EC) Oscillator

• Primary Oscillator with PLL

• Secondary (LP) Oscillator

• Low-Power RC (LPRC) Oscillator

• FRC Oscillator with postscaler

8.1.1

SYSTEM CLOCK SOURCES

8.1.1.1

Fast RC

The Fast RC (FRC) internal oscillator runs at a nominal

frequency of 7.37 MHz. User software can tune the

FRC frequency. User software can optionally specify a

factor (ranging from 1:2 to 1:256) by which the FRC

clock frequency is divided. This factor is selected using

the FRCDIV<2:0> bits (CLKDIV<10:8>).

8.1.1.2

Primary

The primary oscillator can use one of the following as

its clock source:

• XT (Crystal): Crystals and ceramic resonators in

the range of 3 MHz to 10 MHz. The crystal is

connected to the OSC1 and OSC2 pins.

• HS (High-Speed Crystal): Crystals in the range of

10 MHz to 40 MHz. The crystal is connected to

the OSC1 and OSC2 pins.

• EC (External Clock): The external clock signal is

directly applied to the OSC1 pin.

8.1.1.3

Secondary

The secondary (LP) oscillator is designed for low power

and uses a 32.768 kHz crystal or ceramic resonator.

The LP oscillator uses the SOSCI and SOSCO pins.

8.1.1.4

Low-Power RC

The LPRC (Low-Power RC) internal oscIllator runs at a

nominal frequency of 32.768 kHz. It is also used as a

reference clock by the Watchdog Timer (WDT) and

Fail-Safe Clock Monitor (FSCM).

8.1.1.5

FRC

The clock signals generated by the FRC and primary

oscillators can be optionally applied to an on-chip

Phase Locked Loop (PLL) to provide a wide range of

output

frequencies

for

device

operation.

PLL

configuration is described in Section 8.1.3 “PLL

Configuration”.

The FRC frequency depends on the FRC accuracy

(see Table 24-18) and the value of the FRC Oscillator

Tuning register (see Register 8-4).

8.1.2

SYSTEM CLOCK SELECTION

The oscillator source used at a device Power-on

Reset event is selected using Configuration bit

settings. The oscillator Configuration bit settings are

located in the Configuration registers in the program

memory. (Refer to Section 21.1 “Configuration

Bits” for further details.) The Initial Oscillator

Selection

Configuration

bits,

FNOSC<2:0>

(FOSCSEL<2:0>), and the Primary Oscillator Mode

Select

Configuration

bits,

POSCMD<1:0>

(FOSC<1:0>), select the oscillator source that is used

at a Power-on Reset. The FRC primary oscillator is

the default (unprogrammed) selection.

The Configuration bits allow users to choose among 12

different clock modes, shown in Table 8-1.

The output of the oscillator (or the output of the PLL if

a PLL mode has been selected) FOSC is divided by 2 to

generate the device instruction clock (FCY) and the

peripheral clock time base (FP). FCY defines the

operating speed of the device, and speeds up to 40

MHz are supported by the dsPIC33FJ32MC202/204

and dsPIC33FJ16MC304 architecture.

Instruction execution speed or device operating

frequency, FCY, is given by:

EQUATION 8-1:

DEVICE OPERATING

FREQUENCY

8.1.3

PLL CONFIGURATION

The primary oscillator and internal FRC oscillator can

optionally use an on-chip PLL to obtain higher speeds

of operation. The PLL provides significant flexibility in

selecting the device operating speed. A block diagram

of the PLL is shown in Figure 8-2.

The output of the primary oscillator or FRC, denoted as

‘FIN’, is divided down by a prescale factor (N1) of 2, 3,

... or 33 before being provided to the PLL’s Voltage

Controlled Oscillator (VCO). The input to the VCO must

be selected in the range of 0.8 MHz to 8 MHz. The

prescale

factor

‘N1’

selected

using

the

PLLPRE<4:0> bits (CLKDIV<4:0>).

The PLL Feedback Divisor, selected using the

PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor ‘M’,

by which the input to the VCO is multiplied. This factor

must be selected such that the resulting VCO output

frequency is in the range of 100 MHz to 200 MHz.

The VCO output is further divided by a postscale factor

‘N2.’ This factor is selected using the PLLPOST<1:0>

bits (CLKDIV<7:6>). ‘N2’ can be either 2, 4 or 8, and

must be selected such that the PLL output frequency

(FOSC) is in the range of 12.5 MHz to 80 MHz, which

generates device operating speeds of 6.25-40 MIPS.

FCY

FOSC

-------------

DSPIC33FJMC202ESS 数据表(PDF) 102 Page - Microchip Technology

DSPIC33FJMC202ESS 数据表(HTML) 102 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载