MCP602-ESLASHP datasheet(12/34 Pages) MICROCHIP

12 / 34 page

MCP601/1R/2/3/4

DS21314G-page 12

4.0

APPLICATIONS INFORMATION

The MCP601/1R/2/3/4 family of op amps are fabricated

on Microchip’s state-of-the-art CMOS process. They

are unity-gain stable and suitable for a wide range of

general purpose applications.

4.1

Inputs

4.1.1

PHASE REVERSAL

The MCP601/1R/2/3/4 op amp is designed to prevent

phase reversal when the input pins exceed the supply

voltages.

Figure 2-34

shows

the

input

voltage

exceeding the supply voltage without any phase

reversal.

4.1.2

INPUT VOLTAGE AND CURRENT

LIMITS

The ESD protection on the inputs can be depicted as

shown in Figure 4-1. This structure was chosen to

protect the input transistors, and to minimize input bias

current (IB). The input ESD diodes clamp the inputs

when they try to go more than one diode drop below

VSS. They also clamp any voltages that go too far

above VDD; their breakdown voltage is high enough to

allow normal operation, and low enough to bypass

quick ESD events within the specified limits.

FIGURE 4-1:

Simplified Analog Input ESD

Structures.

In order to prevent damage and/or improper operation

of these op amps, the circuit they are in must limit the

currents and voltages at the VIN+ and VIN– pins (see

Absolute Maximum Ratings † at the beginning of

Section 1.0 “Electrical Characteristics”). Figure 4-2

shows the recommended approach to protecting these

inputs. The internal ESD diodes prevent the input pins

(VIN+ and VIN–) from going too far below ground, and

the resistors R1 and R2 limit the possible current drawn

out of the input pins. Diodes D1 and D2 prevent the

input pins (VIN+ and VIN–) from going too far above

VDD, and dump any currents onto VDD. When

implemented as shown, resistors R1 and R2 also limit

the current through D1 and D2.

FIGURE 4-2:

Protecting the Analog

Inputs.

It is also possible to connect the diodes to the left of

resistors R1 and R2. In this case, current through the

diodes D1 and D2 needs to be limited by some other

mechanism. The resistors then serve as in-rush current

limiters; the DC current into the input pins (VIN+ and

VIN–) should be very small.

A significant amount of current can flow out of the

inputs when the common mode voltage (VCM) is below

ground (VSS); see Figure 2-34. Applications that are

high impedance may need to limit the useable voltage

range.

4.1.3

NORMAL OPERATION

The Common Mode Input Voltage Range (VCMR)

includes ground in single-supply systems (VSS), but

does not include VDD. This means that the amplifier

input behaves linearly as long as the Common Mode

Input Voltage (VCM) is kept within the specified VCMR

limits (VSS–0.3V to VDD–1.2V at +25°C).

Figure 4-3 shows a unity gain buffer. Since VOUT is the

same voltage as the inverting input, VOUT must be kept

below VDD–1.2V for correct operation.

FIGURE 4-3:

Unity Gain Buffer has a

Limited VOUT Range.

Bond

Pad

Bond

Pad

Bond

Pad

VDD

VIN+

VSS

Input

Stage

Bond

Pad

VIN–

MCP60X

VDD

R1 >

VSS – (minimum expected V1)

2mA

R2 >

VSS – (minimum expected V2)

2mA

MCP60X

VOUT

–

VIN

MCP602-E/P 数据表(PDF) 12 Page - Microchip Technology

MCP602-E/P 数据表(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表下载

链接网址

MCP602-E/P 数据表(PDF) 12 Page - Microchip Technology

MCP602-E/P 数据表(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表 下载

链接网址

数据表下载