LT1818 datasheet(11/28 Pages) LINER

11 / 28 page

LT1806/LT1807

18067fc

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: The inputs are protected by back-to-back diodes. If the differential

input voltage exceeds 1.4V, the input current should be limited to less

than 10mA. This parameter is guaranteed to meet speciﬁed performance

through design and/or characterization. It is not 100% tested.

Note 3: A heat sink may be required to keep the junction temperature below

the absolute maximum rating when the output is shorted indeﬁnitely.

Note 4: The LT1806C/LT1806I and LT1807C/LT1807I are guaranteed

functional over the temperature range of –40°C and 85°C.

Note 5: The LT1806C/LT1807C are guaranteed to meet speciﬁed

performance from 0°C to 70°C. The LT1806C/LT1807C are designed,

characterized and expected to meet speciﬁed performance from –40°C to

85°C but are not tested or QA sampled at these temperatures. The LT1806I/

LT1807I are guaranteed to meet speciﬁed performance from –40°C to 85°C.

Note 6: Minimum supply voltage is guaranteed by power supply rejection

ratio test.

Note 7: Output voltage swings are measured between the output and

power supply rails.

Note 8: This parameter is not 100% tested.

Note 9: Thermal resistance varies depending upon the amount of PC board

metal attached to the V – pin of the device.

θJA is speciﬁed for a certain

amount of 2oz copper metal trace connecting to the V – pin as described in

the thermal resistance tables in the Applications Information section.

Note 10: Matching parameters are the difference between the two

ampliﬁers of the LT1807.

ELECTRICAL CHARACTERISTICS The l denotes the speciﬁcations which apply over the −40°C < T

A < 85°C

temperature range. VS = ±5V, VSHDN = open; VCM = 0V, VOUT = 0V, unless otherwise noted. (Note 5)

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

tOFF

Turn-Off Time

VSHDN = 4.5V to 0.3V, RL = 100Ω

GBW

Gain-Bandwidth Product

Frequency = 6MHz

125

290

MHz

Slew Rate

AV = –1, RL = 1k, VO = ±4V,

Measure at VO = ±3V

100

V/μs

FPBW

Full-Power Bandwidth

VO = 8VP-P

MHz

TYPICAL PERFORMANCE CHARACTERISTICS

INPUT OFFSET VOLTAGE (μV)

–500

300

18067 G01

–300

–100

100

500

VS = 5V, 0V

VCM = 0V

INPUT OFFSET VOLTAGE (μV)

–500

300

18067 G02

–300

–100

100

500

VS = 5V, 0V

VCM = 5V

INPUT OFFSET VOLTAGE (μV)

–500

300

18067 G03

–300

–100

100

500

VS = 5V, 0V

VOS Distribution, VCM = 0V

(PNP Stage)

VOS Distribution, VCM = 5V

(NPN Stage)

ΔVOS Shift for VCM = 0V to 5V

LT1818 数据表(PDF) 11 Page - Linear Technology

LT1818 数据表(HTML) 11 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载

链接网址

LT1818 数据表(PDF) 11 Page - Linear Technology

LT1818 数据表(HTML) 11 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表 下载

链接网址

数据表下载