PIC16LF1906-IPTQTP datasheet(63/288 Pages) MICROCHIP

63 / 288 page

 2011 Microchip Technology Inc.

Preliminary

DS41569A-page 63

PIC16LF1904/6/7

6.3

Clock Switching

The system clock source can be switched between

external and internal clock sources via software using

the System Clock Select (SCS) bits of the OSCCON

using the SCS bits:

• Default system oscillator determined by FOSC

bits in Configuration Word 1

• Secondary oscillator 32 kHz crystal

• Internal Oscillator Block (INTOSC)

6.3.1

SYSTEM CLOCK SELECT (SCS)

BITS

The System Clock Select (SCS) bits of the OSCCON

the CPU and peripherals.

• When the SCS bits of the OSCCON register = 00,

the system clock source is determined by value of

the FOSC<1:0> bits in the Configuration Word 1.

• When the SCS bits of the OSCCON register = 01,

the system clock source is the secondary

oscillator.

• When the SCS bits of the OSCCON register = 1x,

the system clock source is chosen by the internal

oscillator frequency selected by the IRCF<3:0>

bits of the OSCCON register. After a Reset, the

SCS bits of the OSCCON register are always

cleared.

When switching between clock sources, a delay is

required to allow the new clock to stabilize. These oscil-

lator delays are shown in Table 6-1.

6.3.2

OSCILLATOR START-UP TIME-OUT

STATUS (OSTS) BIT

The Oscillator Start-up Time-out Status (OSTS) bit of

the OSCSTAT register indicates whether the system

clock is running from the external clock source, as

defined by the FOSC<1:0> bits in the Configuration

Word 1, or from the internal clock source. The OST

does not reflect the status of the secondary oscillator.

6.3.3

SECONDARY OSCILLATOR

The secondary oscillator is a separate crystal oscillator

associated with the Timer1 peripheral. It is optimized

for timekeeping operations with a 32.768 kHz crystal

connected between the T1OSI and T1CKI/T1OSO

device pins.

The secondary oscillator is enabled using the

T1OSCEN control bit in the T1CON register. See

Section 17.0 “Timer1 Module with Gate Control”

for

more information about the Timer1 peripheral.

6.3.4

SECONDARY OSCILLATOR READY

(T1OSCR) BIT

The user must ensure that the secondary oscillator is

ready to be used before it is selected as a system clock

source. The Secondary Oscillator Ready (T1OSCR) bit

of the OSCSTAT register indicates whether the

secondary oscillator is ready to be used. After the

T1OSCR bit is set, the SCS bits can be configured to

select the secondary oscillator.

PIC16LF1906-IPTQTP 数据表(PDF) 63 Page - Microchip Technology

PIC16LF1906-IPTQTP 数据表(HTML) 63 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载