I2CSTAT datasheet(137/210 Pages) MICROCHIP

137 / 210 page

DS70139G-page 137

dsPIC30F2011/2012/3012/3013

18.0

INSTRUCTION SET SUMMARY

The

dsPIC30F

instruction

set

adds

many

enhancements to the previous PIC® MCU instruction

sets, while maintaining an easy migration from

PIC

MCU instruction sets.

Most instructions are a single program memory word

(24 bits). Only three instructions require two program

memory locations.

Each single-word instruction is a 24-bit word divided

into an 8-bit opcode which specifies the instruction

type, and one or more operands which further specify

the operation of the instruction.

The instruction set is highly orthogonal and is grouped

into five basic categories:

• Word or byte-oriented operations

• Bit-oriented operations

• Literal operations

• DSP operations

• Control operations

Table 18-1 shows the general symbols used in

describing the instructions.

The dsPIC30F instruction set summary in Table 18-2

lists all the instructions, along with the status flags

affected by each instruction.

Most word or byte-oriented W register instructions

(including

barrel

shift

instructions)

have

three

operands:

• The first source operand which is typically a

• The second source operand which is typically a

• The destination of the result which is typically a

However, word or byte-oriented file register instructions

have two operands:

• The file register specified by the value ‘f’

• The destination, which could either be the file

‘WREG’

Most

bit-oriented

instructions

(including

simple

rotate/shift instructions) have two operands:

• The W register (with or without an address

modifier) or file register (specified by the value of

‘Ws’ or ‘f’)

• The bit in the W register or file register

(specified by a literal value or indirectly by the

contents of register ‘Wb’)

The literal instructions that involve data movement may

use some of the following operands:

• A literal value to be loaded into a W register or file

• The W register or file register where the literal

value is to be loaded (specified by ‘Wb’ or ‘f’)

However, literal instructions that involve arithmetic or

logical operations use some of the following operands:

• The first source operand which is a register ‘Wb’

without any address modifier

• The second source operand which is a literal

value

• The destination of the result (only if not the same

as the first source operand) which is typically a

The MAC class of DSP instructions may use some of the

following operands:

• The accumulator (A or B) to be used (required

operand)

• The W registers to be used as the two operands

• The X and Y address space prefetch operations

• The X and Y address space prefetch destinations

• The accumulator write-back destination

The other DSP instructions do not involve any

multiplication, and may include:

• The accumulator to be used (required)

• The source or destination operand (designated as

Wso or Wdo, respectively) with or without an

address modifier

• The amount of shift specified by a W register ‘Wn’

or a literal value

The control instructions may use some of the following

operands:

• A program memory address

• The mode of the table read and table write

instructions

Note:

This data sheet summarizes features of

this group of dsPIC30F devices and is not

intended to be a complete reference

source. For more information on the CPU,

peripherals,

descriptions

and

general device functionality, refer to the

“dsPIC30F Family Reference Manual”

(DS70046). For more information on the

device instruction set and programming,

refer to the “dsPIC30F Programmer’s

Reference Manual” (DS70030).

I2CSTAT 数据表(PDF) 137 Page - Microchip Technology

I2CSTAT 数据表(HTML) 137 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载