数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

AN394 数据表(PDF) 6 Page - STMicroelectronics

部件名 AN394
功能描述  Within STMicroelectronics
PDF  10 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

AN394 数据表(HTML) 6 Page - STMicroelectronics

Back Button AN394 Datasheet HTML 2Page - STMicroelectronics AN394 Datasheet HTML 3Page - STMicroelectronics AN394 Datasheet HTML 4Page - STMicroelectronics AN394 Datasheet HTML 5Page - STMicroelectronics AN394 Datasheet HTML 6Page - STMicroelectronics AN394 Datasheet HTML 7Page - STMicroelectronics AN394 Datasheet HTML 8Page - STMicroelectronics AN394 Datasheet HTML 9Page - STMicroelectronics AN394 Datasheet HTML 10Page - STMicroelectronics  
Zoom Inzoom in Zoom Outzoom out
 6 / 10 page
background image
AN394 - APPLICATION NOTE
6/10
Figure 8. Oscilloscope Plot, R = 10 k
Ω, C = 330 pF, RC = 3.3 µs
In order to avoid over reducing the clock frequency, the following techniques can be used to minimize the
R and C values:
s
To minimize the bus capacitance:
– the EEPROM device should be position as close as possible to the D-driver/Q-receiver circuitry (the ca-
pacitance is proportional to the surface area of the bus line).
– As few devices as possible should share the D/Q bus (the capacitance is proportional to the number of
input gates connected to the bus).
s
To minimize the resistor value:
– Find, from the data sheet, the maximum current that the D driver can source, and divide this value into
the value of Vcc.
– Find the maximum transient current that the power supply can source without glitches being introduced
on to the power lines, and divide this value into the value of Vcc.
– It is up to the designer to decide the best trade-off, based upon his specific application’s requirements,
but the resistor value should not be less than the higher of the two values calculated above.
INTERFACE WITH CMOS CIRCUITS
The MICROWIRE EEPROM specification makes these devices compatible with TTL input/output levels.
When interfacing these devices to CMOS circuits, however, some precautions must be taken, to ensure
the correct interpretation of the logic levels.
Since the output-high level is close to VCC, and the output-low level is close to 0 V, there are no difficulties
in driving the D, S and C inputs of the EEPROM devices.
For the Q output, though, the minimum output-high level is specified as being 2.4 V, which is lower than
the minimum input-high level of CMOS (3.5 V for Vcc = 5 V). A common practice is to connect a pull-up
resistor, Rp, between the Q output and Vcc.
This solution works well when D and Q are separate. However, it raises some difficulties when D and Q
are tied together.
Ai02427
5V
C clock
D/Q bus
Q output
D driver enable
(1 = disabled)
10
µS



Html Pages

1 2 3 4 5 6 7 8 9 10


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com