M28W320ECT datasheet(5/53 Pages) STMICROELECTRONICS

5 / 53 page

5/53

M28W320ECT, M28W320ECB

SUMMARY DESCRIPTION

The M28W320EC is a 32 Mbit (2 Mbit x 16) non-

volatile Flash memory that can be erased electri-

cally at the block level and programmed in-system

on a Word-by-Word basis. These operations can

be performed using a single low voltage (2.7 to

3.6V) supply. VDDQ allows to drive the I/O pin

down to 1.65V. An optional 12V VPP power supply

is provided to speed up customer programming.

The device features an asymmetrical blocked ar-

chitecture. The M28W320EC has an array of 71

blocks: 8 Parameter Blocks of 4 KWord and 63

Main Blocks of 32 KWord. M28W320ECT has the

Parameter Blocks at the top of the memory ad-

dress space while the M28W320ECB locates the

Parameter Blocks starting from the bottom. The

memory maps are shown in Figure 5, Block Ad-

dresses.

The M28W320EC features an instant, individual

block locking scheme that allows any block to be

locked or unlocked with no latency, enabling in-

stant code and data protection. All blocks have

three levels of protection. They can be locked and

locked-down individually preventing any acciden-

tal programming or erasure. There is an additional

hardware protection against program and erase.

When VPP ≤ VPPLK all blocks are protected against

program or erase. All blocks are locked at Power

Up.

Each block can be erased separately. Erase can

be suspended in order to perform either read or

program in any other block and then resumed.

Program can be suspended to read data in any

other block and then resumed. Each block can be

programmed and erased over 100,000 cycles.

The device includes a Protection Register to in-

crease the protection of a system design. The Pro-

tection Register is divided into two segments, the

first is a 64 bit area which contains a unique device

number written by ST, while the second is a 128 bit

area, one-time-programmable by the user. The

user programmable segment can be permanently

protected. Figure 6, shows the Protection Register

Memory Map.

Program and Erase commands are written to the

Command Interface of the memory. An on-chip

Program/Erase Controller takes care of the tim-

ings necessary for program and erase operations.

The end of a program or erase operation can be

detected and any error conditions identified. The

command set required to control the memory is

consistent with JEDEC standards.

The memory is offered in TSOP48 (10 X 20mm)

and TFBGA47 (6.39 x 6.37mm, 0.75mm pitch)

packages and is supplied with all the bits erased

(set to ’1’).

Figure 2. Logic Diagram

Table 1. Signal Names

A0-A20

Address Inputs

DQ0-DQ15

Data Input/Output

Chip Enable

Output Enable

Write Enable

Reset

Write Protect

VDD

Core Power Supply

VDDQ

Power Supply for

Input/Output

VPP

Optional Supply Voltage for

Fast Program & Erase

VSS

Ground

Not Connected Internally

AI05517

A0-A20

DQ0-DQ15

VDD

M28W320ECT

M28W320ECB

VSS

VDDQ VPP

M28W320ECT 数据表(PDF) 5 Page - STMicroelectronics

M28W320ECT 数据表(HTML) 5 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

数据表下载