| 数据搜索系统,热门电子元器件搜索 |
|
UCS81003 数据表(PDF) 49 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS81003 数据表(HTML) 49 Page - Microchip Technology |
|
49 / 108 page ![]() 2014 Microchip Technology Inc. DS20005334A-page 49 UCS81003 REGISTER 10-2: OTHER STATUS REGISTER (ADDRESS 0FH) U-x U-x R-0 R-0 R-0 R-0 R-0 R-0 — — ALERT_PIN ADET_PIN CHG_ACT EM_ACT EM_STEP<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented bit 5 ALERT_PIN: Reflects the status of the ALERT# pin. This bit is set and cleared as the ALERT# pin changes states. 1 = ALERT# pin is asserted low 0 = ALERT# pin is released bit 4 ADET_PIN: Reflects the status of the A_DET# pin. When set, indicates that the A_DET# pin is asserted low. This bit is set and cleared as the A_DET# pin changes states. (Note 1) 1 = A_DET# pin is asserted low 0 = A_DET# pin is released bit 3 CHG_ACT: This bit is automatically set when IBUS > IBUS_CHG and cleared when IBUS < IBUS_CHG. (Note 2) 1 =IBUS > IBUS_CHG 0 =IBUS < IBUS_CHG bit 2 EM_ACT: Indicates that the UCS81003 is in the Active state and emulating. The actual profile that is being applied is identified by PRE_EM_SEL<3:0> (see Section 10.12.1 “Applied Charger Emulation Register”). This bit is set and cleared automatically. (Note 3) 1 = Device is in Active state and emulating 0 = Device is not emulating bit 1-0 EM_STEP<1:0>: Indicates which stimulus / response pair is currently being applied by the charger emu- lation profile as shown below. These bits are set and cleared automatically. Note that the Legacy charger emulation profiles and the BC1.2 DCP charger emulation profile do not use Stimulus / Response Pair #3. 00 = None Applied. Waiting for current. 01 = Stimulus/Response #1 10 = Stimulus/Response #2 00 = Stimulus/Response #3 if applicable Note 1: If S0 is '1', PWR_EN is enabled, and VS is not present, the ADET_PIN bit will cycle if the current draw exceeds the current capacity of the bypass switch. 2: The CHG_ACT bit does not indicate that a portable device has accepted one of the charger emulation pro- files. This bit will cycle during the Dedicated Charger Emulation Cycle. 3: The EM_ACT bit does not indicate that a portable device has accepted one of the emulation profiles. This bit will cycle during the Dedicated Charger Emulation Cycle. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |