 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
UCS81003 数据表(PDF) 73 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS81003 数据表(HTML) 73 Page - Microchip Technology |
|
|
73 / 108 page  2014 Microchip Technology Inc. DS20005334A-page 73 UCS81003 bit 3-0 S2_R2<3:0>: Defines the stimulus response as shown below: 0000 = Remove previous response on DPOUT and DMOUT 0001 = Apply voltage on DPOUT (Note 1). 0010 = Apply voltage on DMOUT (Note 2). 0011 = Apply voltage on DPOUT and DMOUT. 0100 = Connect resistor from DPOUT to GND (Note 1). 0101 = Do not use. 0110 = Connect voltage divider from VBUS to GND with “center” at DPOUT (Note 1). 0111 = Connect resistor form DMOUT to GND (Note 2). 1000 = Do not use. 1001 = Connect voltage divider from VBUS to GND with “center” at DMOUT (Note 2). 1010 = Connect 200resistor from D POUT to DMOUT. 1011 = Do not use. 1100 = Connect voltage divider from VBUS to GND with ‘center’ at DPOUT and DMOUT. 1101 = Connect resistor from DPOUT to GND and DMOUT to GND. 1110 = If STIM2 = 000, the 15 k pull down resistors applied to D POUT and DMOUT during emulation reset are not removed. If STIM2 = 111, the 15 k pull down resistors applied to D POUT and DMOUT during emulation reset are removed. For all other STIM2 settings, whatever was applied is not changed. 1111 = Same as 1110 case above. Note 1: If STIM2<2:0> = 000b and no other response was applied to the DPOUT pin, the 15 k pull-down resistor applied to the DPOUT pin during emulation reset is not removed. Otherwise, the previous response is left on the DPOUT pin (if applicable) or the 15 k pull-down resistor is removed. 2: If STIM2<2:0> = 000b and no other response was applied to the DMOUT pin, the 15 k pull-down resistor applied to the DMOUT pin during emulation reset is not removed. Otherwise, the previous response is left on the DMOUT pin (if applicable) or the 15 k pull-down resistor is removed. REGISTER 10-30: PRELOADED EMULATION STIMULUS 2 CONFIGURATION 3 REGISTER (ADDRESS 37H)(Note 1) U-x U-x R-0 R-0 R-0 R-0 R-0 R-0 — — S2_PUPD<1:0> S2_TH<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented bit 5-4 S2_PUPD<1:0>: Determines the magnitude of the pull-down current applied on the DPOUT and DMOUT pins when the stimulus response is to apply a voltage and the voltage magnitude is set at pull-down (0000b). The bit decode is as follows: 00 =10 µA 01 =50 µA 10 =100 µA 11 =150 µA REGISTER 10-29: PRELOADED EMULATION STIMULUS 2 CONFIGURATION 2 REGISTER (ADDRESS 36H) (CONTINUED) |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
