STM32F091CB datasheet(67/127 Pages) STMICROELECTRONICS

67 / 127 page

DocID026284 Rev 3

67/127

STM32F091xB STM32F091xC

Electrical characteristics

6.3.6

Wakeup time from low-power mode

The wakeup times given in Table 36 are the latency between the event and the execution of

the first user instruction. The device goes in low-power mode after the WFE (Wait For

Event) instruction, in the case of a WFI (Wait For Interruption) instruction, 16 CPU cycles

must be added to the following timings due to the interrupt latency in the Cortex M0

architecture.

The SYSCLK clock source setting is kept unchanged after wakeup from Sleep mode.

During wakeup from Stop or Standby mode, SYSCLK takes the default setting: HSI 8 MHz.

The wakeup source from Sleep and Stop mode is an EXTI line configured in event mode.

The wakeup source from Standby mode is the WKUP1 pin (PA0).

All timings are derived from tests performed under the ambient temperature and supply

voltage conditions summarized in Table 24: General operating conditions.

6.3.7

External clock source characteristics

High-speed external user clock generated from an external source

In bypass mode the HSE oscillator is switched off and the input pin is a standard GPIO.

The external clock signal has to respect the I/O characteristics in Section 6.3.14. However,

the recommended clock input waveform is shown in Figure 15: High-speed external clock

source AC timing diagram.

Table 36. Low-power mode wakeup timings

Symbol

Parameter

Conditions

Typ @VDD = VDDA

Max Unit

= 2.0 V = 2.4 V = 2.7 V

= 3 V

= 3.3 V

tWUSTOP

Wakeup from Stop

mode

Regulator in run

mode

3.23.1

2.92.9

2.8

µs

Regulator in low

power mode

7.05.8

5.24.9

4.6

tWUSTANDBY

Wakeup from

Standby mode

60.4

55.6

53.5

tWUSLEEP

Wakeup from Sleep

mode

4 SYSCLK cycles

Table 37. High-speed external user clock characteristics

Symbol

Parameter(1)

Min

Typ

Max

Unit

fHSE_ext User external clock source frequency

MHz

VHSEH

OSC_IN input pin high level voltage

0.7 VDDIOx

-VDDIOx

VHSEL

OSC_IN input pin low level voltage

VSS

0.3 VDDIOx

tw(HSEH)

tw(HSEL)

OSC_IN high or low time

tr(HSE)

tf(HSE)

OSC_IN rise or fall time

STM32F091CB 数据表(PDF) 67 Page - STMicroelectronics

STM32F091CB 数据表(HTML) 67 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

STM32F091CB 数据表(PDF) 67 Page - STMicroelectronics

STM32F091CB 数据表(HTML) 67 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载