AM29PLI60C datasheet(16/44 Pages) AMD

16 / 44 page

June 12, 2002

Am29PL160C

HARDWARE DATA PROTECTION

The command sequence requirement of unlock cycles

for programming or erasing provides data protection

against inadvertent writes (refer to Table 10 for com-

mand definitions). In addition, the following hardware

data protection measures prevent accidental erasure

or programming, which might otherwise be caused by

spurious system level signals during VCC power-up

and power-down transitions, or from system noise.

Low VCC Write Inhibit

When VCC is less than VLKO, the device does not ac-

cept any write cycles. This protects data during VCC

power-up and power-down. The command register

and all internal program/erase circuits are disabled,

and the device resets. Subsequent writes are ignored

until VCC is greater than VLKO. The system must pro-

vide the proper signals to the control pins to prevent

unintentional writes when VCC is greater than VLKO.

Write Pulse “Glitch” Protection

Noise pulses of less than 5 ns (typical) on OE#, CE# or

WE# do not initiate a write cycle.

Logical Inhibit

Write cycles are inhibited by holding any one of OE# =

VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,

CE# and WE# must be a logical zero while OE# is a

logical one.

Power-Up Write Inhibit

If WE# = CE# = VIL and OE# = VIH during power up,

the device does not accept commands on the rising

edge of WE#. The internal state machine is automati-

cally reset to reading array data on power-up.

Table 9.

Primary Vendor-Specific Extended Query

Addresses

(Word Mode)

Addresses

(Byte Mode)

Data

Description

40h

41h

42h

80h

82h

84h

0050h

0052h

0049h

Query-unique ASCII string “PRI”

43h

86h

0031h

Major version number, ASCII

44h

88h

0030h

Minor version number, ASCII

45h

8Ah

0000h

Address Sensitive Unlock

0 = Required, 1 = Not Required

46h

8Ch

0002h

Erase Suspend

0 = Not Supported, 1 = To Read Only, 2 = To Read & Write

47h

8Eh

0001h

Sector Protect

0 = Not Supported, X = Number of sectors in per group

48h

90h

0001h

Sector Temporary Unprotect

00 = Not Supported, 01 = Supported

49h

92h

0004h

Sector Protect/Unprotect scheme

01 = 29F040 mode, 02 = 29F016 mode,

03 = 29F400 mode, 04 = 29LV800A mode

4Ah

94h

0000h

Simultaneous Operation

00 = Not Supported, 01 = Supported

4Bh

96h

0000h

Burst Mode Type

00 = Not Supported, 01 = 4 Word Linear Burst, 02 = 8 Word Linear Burst,

03 = 32 Linear Burst, 04 = 4 Word Interleave Burst

4Ch

98h

0002h

Page Mode Type

00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page

AM29PLI60C 数据表(PDF) 16 Page - Advanced Micro Devices

AM29PLI60C 数据表(HTML) 16 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载

链接网址

AM29PLI60C 数据表(PDF) 16 Page - Advanced Micro Devices

AM29PLI60C 数据表(HTML) 16 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表 下载

链接网址

数据表下载