TNETV2666FIBZWT datasheet(198/249 Pages) TI1

198 / 249 page

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

CLKX

FSX

TMS320C6424

SPRS347D – MARCH 2007 – REVISED DECEMBER 2009

www.ti.com

Table 6-43. Timing Requirements for McBSP as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0 (1) (2)

(see Figure 6-27 ) (continued)

-7/-6/-5/-4

-L/-Q6/-Q5/-Q4

NO.

UNIT

MASTER

SLAVE

MIN

MAX

MIN

MAX

th(CKXL-DRV)

Hold time, DR valid after CLKX low

5 + 6P

Table 6-44. Switching Characteristics Over Recommended Operating Conditions for McBSP as SPI

Master or Slave: CLKSTP = 10b, CLKXP = 0(1) (2) (see Figure 6-27)

-7/-6/-5/-4

-L/-Q6/-Q5/-Q4

NO.

PARAMETER

UNIT

MASTER(3)

SLAVE

MIN

MAX

MIN

MAX

th(CKXL-FXL)

Hold time, FSX low after CLKX low(4)

T - 4

T + 5.5

td(FXL-CKXH)

Delay time, FSX low to CLKX high(5)

L - 4

L + 4

td(CKXH-DXV)

Delay time, CLKX high to DX valid

-4

5.5

3P + 2.8

5P + 17

Disable time, DX high impedance following

tdis(CKXL-DXHZ)

L - 6

L + 7.5

last data bit from CLKX low

Disable time, DX high impedance following

tdis(FXH-DXHZ)

P + 3

3P + 17

last data bit from FSX high

td(FXL-DXV)

Delay time, FSX low to DX valid

2P + 1.8

4P + 17

(1)

P = SYSCLK3 period in ns. For example, when running parts at 600 MHz, use P = 10ns.

(2)

For all SPI Slave modes, the rate of the internal clock CLKG must be at least 8 times faster than that of the SPI data rate. User should

program sample rate generator to achieve maximum CLKG by setting CLKSM = CLKGDV = 1.

(3)

S = Sample rate generator input clock = 2P if CLKSM = 1 (P = SYSCLK3 period)

S = Sample rate generator input clock = 2P_clks if CLKSM = 0 (P_clks = CLKS period)

T = CLKX period = (1 + CLKGDV) * S

H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even

H = (CLKGDV + 1)/2 * S if CLKGDV is odd

L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even

L = (CLKGDV + 1)/2 * S if CLKGDV is odd

(4)

FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input

on FSX and FSR is inverted before being used internally.

CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP

CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP

(5)

FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master

clock (CLKX).

Figure 6-27. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0

198

Peripheral Information and Electrical Specifications

Submit Documentation Feedback

Product Folder Link(s): TMS320C6424

TNETV2666FIBZWT 数据表(PDF) 198 Page - Texas Instruments

TNETV2666FIBZWT 数据表(HTML) 198 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载