AT89C51AC3-RDTIM datasheet(121/141 Pages) ATMEL

121 / 141 page

121

AT89C51AC3

4383A–8051–10/04

Notes:

1. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 67.), VIL =

SS + 0.5V,

IH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure

64.).

2. Idle I

CC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC -

0.5V; XTAL2 N.C; Port 0 = V

CC; EA = RST = VSS (see Figure 65.).

3. Power-down I

CC is measured with all output pins disconnected; EA = VCC, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Fig-

ure 66.). In addition, the WDT must be inactive and the POF flag must be set.

4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the V

OLs of ALE and Ports 1

and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0

transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed

0.45V with maxi V

OL peak 0.6V. A Schmitt Trigger use is not necessary.

5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature.

6. Under steady state (non-transient) conditions, I

OL must be externally limited as follows:

Maximum I

OL per port pin: 10 mA

Maximum I

OL per 8-bit port:

Port 0: 26 mA

Ports 1, 2, 3 and 4: 15 mA

Maximum total I

OL for all output pins: 71 mA

If I

OL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test conditions.

Figure 64. I

CC Test Condition, Active Mode

Power Supply Current

CCOP = 0.4 Frequency (MHz) + 8

CCIDLE = 0.2 Frequency (MHz) + 8

Vcc = 5.5V(1)(2)

Table 71. DC Parameters in Standard Voltage (Continued)

Symbol

Parameter

Min

Typ(5)

Max

Unit

Test Conditions

VCC

ICC

(NC)

CLOCK

SIGNAL

VCC

All other pins are disconnected.

RST

XTAL2

XTAL1

AT89C51AC3-RDTIM 数据表(PDF) 121 Page - ATMEL Corporation

AT89C51AC3-RDTIM 数据表(HTML) 121 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载