CS5522-AP datasheet(33/56 Pages) CIRRUS

33 / 56 page

CS5521/22/23/24/28

DS317F2

perform a system gain calibration. In either case,

the calibration signals must be within the specified

calibration limits for each specific calibration step

(refer to the ‘System Calibration Specifications’ in

ANALOG CHARACTERISTICS). If a system gain

calibration is performed the following conditions

must be met:

1) Full-scale input must not saturate the 20X in-

strumentation amplifier, if the calibration is on

an input range where the instrumentation am-

plifier is involved.

2) The 1’s density of the modulator must not be

greater than 80 percent (the input to the

∆Σ

modulator must not exceed the maximum input

which Table 1 specifies).

3) The input must not be so small relative to the

range chosen that the resulting gain register’s

content,

decoded

decimal,

exceeds

3.9999998 (see the discussion of operating lim-

its on input span under the Analog Input and

Limitations in Calibration Range sections).

This requires the full scale input voltage to the

modulator to be at least 25 percent of the nom-

inal value.

The converter’s input ranges were chosen to guar-

antee gain calibration accuracy to 1 LSB16 or 16

LSB24 when system gain calibration is performed.

This is useful when a user wants to manually scale

the full scale range of the converter and maintain

accuracy. For example, if a gain calibration is per-

formed with a 2.5 V full scale voltage and a 1.25 V

input range is desired, the user can read the con-

tents of the gain register, shift the register contents

left by 1 bit, and then write the result back to the

gain register. This multiples the gain by 2.

Assuming a system can provide two known voltag-

es, the following equations allow the user to manu-

ally compute the calibration register’s values based

on two uncalibrated conversions (see note). The

offset and gain calibration registers are used to ad-

just a typical conversion as follows:

Rc = (Ru + Co) * Cg / 222.

Calibration can be performed using the following

equations:

Co = (Rc0/G - Ru0)

Cg = 222 * G

where G = (Rc1 - Rc0)/(Ru1-Ru0).

Note: Uncalibrated conversions imply that the gain and off-

set registers are at default {gain register = 0x400000

(Hex) and offset register = 0x000000 (Hex)}.

X20

External

Connections

AIN+

AIN-

CM +

Figure 15. System Calibration of Offset (High Ranges)

X20

External

Connections

Full Scale +

AIN+

AIN-

CM +

Figure 16. System Calibration of Gain (Low Ranges)

X20

External

Connections

Full Scale

AIN+

AIN-

Figure 17. System Calibration of Gain (High Ranges)

CS5522-AP 数据表(PDF) 33 Page - Cirrus Logic

CS5522-AP 数据表(HTML) 33 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载

链接网址

CS5522-AP 数据表(PDF) 33 Page - Cirrus Logic

CS5522-AP 数据表(HTML) 33 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表 下载

链接网址

数据表下载