GD25Q80CSFG datasheet(28/67 Pages) GIGADEVICE

28 / 67 page

3.3V Uniform Sector

Dual and Quad Serial Flash

GD25Q80C

completed, the Write Enable Latch (WEL) bit is reset. A 64KB Block Erase (BE) command applied to a block which is

protected by the Block Protect (BP4, BP3, BP2, BP1, and BP0) bits (see Table1&1a) is not executed.

Figure 20. 64KB Block Erase Sequence Diagram

7.19.

Chip Erase (CE) (60/C7H)

The Chip Erase (CE) command is used to erase all the data of the chip. A Write Enable (WREN) command must

previously have been executed to set the Write Enable Latch (WEL) bit .The Chip Erase (CE) command is entered by driving

CS# Low, followed by the command code on Serial Data Input (SI). CS# must be driven Low for the entire duration of the

sequence.

The Chip Erase command sequence: CS# goes low  sending Chip Erase command  CS# goes high. The

command sequence is shown in Figure21. CS# must be driven high after the eighth bit of the command code has been

latched in; otherwise the Chip Erase command is not executed. As soon as CS# is driven high, the self-timed Chip Erase

cycle (whose duration is tCE) is initiated. While the Chip Erase cycle is in progress, the Status Register may be read to check

the value of the Write in Progress (WIP) bit. The Write in Progress (WIP) bit is 1 during the self-timed Chip Erase cycle, and

is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset.

The Chip Erase (CE) command is executed if the Block Protect (BP2, BP1, and BP0) bits are 0 and CMP=0 or the Block

Protect (BP2, BP1, and BP0) bits are 1 and CMP=1. The Chip Erase (CE) command is ignored if one or more sectors are

protected.

Figure 21. Chip Erase Sequence Diagram

7.20.

Deep Power-Down (DP) (B9H)

Executing the Deep Power-Down (DP) command is the only way to put the device in the lowest consumption mode

(the Deep Power-Down Mode). It can also be used as an extra software protection mechanism, while the device is not in

active use, since in this mode, the device ignores all Write, Program and Erase commands. Driving CS# high deselects the

device, and puts the device in the Standby Mode (if there is no internal cycle currently in progress). But this mode is not the

Deep Power-Down Mode. The Deep Power-Down Mode can only be entered by executing the Deep Power-Down (DP)

command. Once the device has entered the Deep Power-Down Mode, all commands are ignored except the Release from

Deep Power-Down and Read Device ID (RDI) (ABH) or Enable Reset (66H) and Reset (99H) commands. These commands

can release the device from this mode. The Release from Deep Power-Down and Read Device ID (RDI) command releases

the device from deep power down mode , also allows the Device ID of the device to be output on SO.

The Deep Power-Down Mode automatically stops at Power-Down, and the device always Power-Up in the Standby

Command

60H or C7H

CS#

SCLK

Command

D8H

CS#

SCLK

29 30 31

MSB

24 Bits Address

23 22

GD25Q80CSFG 数据表(PDF) 28 Page - GigaDevice Semiconductor (Beijing) Inc.

GD25Q80CSFG 数据表(HTML) 28 Page - GigaDevice Semiconductor (Beijing) Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

数据表下载