CS7666 datasheet(18/42 Pages) CIRRUS

18 / 42 page

CS7666

DS302PP1

board are tied to the secondary I2C port of the

CS7666. WRITE and READ packets only are de-

fined in four-byte mode. Independent address set

operations to slave devices on the secondary I2C

bus is not allowed in four-byte mode. Four-byte

mode is active when the 4BYTEMODE pin (pin 1)

is logic high.

Write Operations in Four-Byte mode

All WRITE operations from an external controller,

through the CS7666, to any slave device must use

the four-byte mode; this includes writing to the

CS7666 itself. The external controller sends a four-

byte WRITE command to the CS7666 which ini-

tiates a WRITE operation to the destination slave

device and sets the I2CBUSY bit in the status reg-

ister (01h). The I2CBUSY bit is cleared when the

write operation on the secondary bus is complete.

The External controller can poll the status register

to check if the CS7666 has completed the com-

mand.

The CS7666 has a one command buffer which al-

lows the external controller to queue one additional

command while the current command is still being

executed. If more than one command is sent before

the I2CBUSY bit is cleared, the CS7666 saves only

the last command and executes it after the current

one is completed. Commands that involve writing

or reading only to CS7666 registers are not put in

the queue but are executed immediately without af-

fecting any transactions occurring on the master

2C interface.

Any attempt by the external I

2C controller to write

to the CS7666 registers while the CS7666 is busy

initializing from an external EEPROM will be ig-

nored. However, reads from the CS7666 are al-

lowed during this time.

If, during a READ or WRITE operation to a slave

device, the CS7666 fails to receive an acknowledge

bit the execution of the command is aborted and the

NODEV bit in the status register is set high. This

bit remains set unless it is explicitly cleared by

writing to it or a new command is written to

CS7666.

Read Operations in Four-Byte Mode

The READ operation in four-byte mode first re-

quires a three-byte READ-TRIGGER packet to the

CS7666. The first byte is the station address of the

CS7666 with the LSB set LOW. The second byte is

the target slave device’s station address with the

LSB (data direction bit) set HIGH. The third byte is

the register address (0..255).

The READ-TRIGGER packet initiates a READ

operation by the CS7666 from the target slave de-

vice on the secondary I

2C bus. The status register

in the CS7666 may be checked to see if the read op-

eration has been completed. The I2CBUSY bit in

status register 01h is set to zero when the operation

is completed.

On completion of a read cycle from the target de-

vice, the CS7666 places the data read into the Slave

Data Hold register at address 19h. The external

controller can read this data through the primary

2C port. This requires first performing an AD-

DRESS SET operation to set the address to 19h and

Byte Sequence

WRITE Format Packet Detail

First Byte

Station Address of CS7666 with LSB

Set LOW

Second Byte

Station Address of target slave

device with LSB Set LOW

Third Byte

Device Register Address (0..255)

Fourth Byte

Table 11. Four-byte WRITE Format Packet

Byte Sequence

READ-TRIGGER format Packet

Details

First Byte

CS7666 Station Address with LSB

Set LOW

Second Byte

Target device Station Address with

LSB Set HIGH

Third Byte

Device Register Address (0..255)

Table 12. READ-TRIGGER packet in four-byte mode

CS7666 数据表(PDF) 18 Page - Cirrus Logic

CS7666 数据表(HTML) 18 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载