LSM303C datasheet(25/53 Pages) STMICROELECTRONICS

25 / 53 page

DocID024975 Rev 2

25/53

LSM303C

Digital interfaces

6.1.1

I2C operation

The transaction on the bus is started through a START (ST) signal. A START condition is

defined as a HIGH-to-LOW transition on the data line while the SCL line is held HIGH. After

this has been transmitted by the master, the bus is considered busy. The next byte of data

transmitted after the start condition contains the address of the slave in the first 7 bits and

the eighth bit tells whether the master is receiving data from the slave or transmitting data to

the slave. When an address is sent, each device in the system compares the first seven bits

after a start condition with its address. If they match, the device considers itself addressed

by the master.

Data transfer with acknowledge is mandatory. The transmitter must release the SDA line

during the acknowledge pulse. The receiver must then pull the data line LOW so that it

remains stable low during the HIGH period of the acknowledge clock pulse. A receiver

which has been addressed is obliged to generate an acknowledge after each byte of data

received.

The I2C embedded inside the LSM303C behaves like a slave device and the following

protocol must be adhered to. In the I2C of the accelerometer sensor, after the START

condition (ST) a slave address is sent, once a slave acknowledge (SAK) has been returned,

an 8-bit sub-address (SUB) is transmitted. The 7 LSb represent the actual register address

while the CTRL_REG4_A (IF_ADD_INC) bit defines the address increment. In the I2C of the

magnetometer sensor, after the START condition (ST) a slave address is sent, once a slave

acknowledge (SAK) has been returned, an 8-bit sub-address (SUB) is transmitted. The 7

LSb represent the actual register address while the MSB enables the address auto

increment. The SUB (register address) is automatically increased to allow multiple data

read/write.

Data are transmitted in byte format (DATA). Each data transfer contains 8 bits. The number

of bytes transferred per transfer is unlimited. Data is transferred with the Most Significant bit

Table 12. Transfer when master is writing one byte to slave

Master

SAD + W

SUB

DATA

Slave

SAK

Table 13. Transfer when master is writing multiple bytes to slave

Master

SAD + W

SUB

DATA

Slave

SAK

Table 14. Transfer when master is receiving (reading) one byte of data from slave

Master

SAD + W

SUB

SAD + R

NMAK

Slave

SAK

DATA

Table 15. Transfer when master is receiving (reading) multiple bytes of data from slave

Master ST SAD+W

SUB

SR SAD+R

MAK

NMAK SP

Slave

SAK

DATA

DAT

DATA

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

LSM303C 数据表(PDF) 25 Page - STMicroelectronics

LSM303C 数据表(HTML) 25 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

数据表下载

链接网址

LSM303C 数据表(PDF) 25 Page - STMicroelectronics

LSM303C 数据表(HTML) 25 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

数据表 下载

链接网址

数据表下载